Jump to content
SAU Community

What Is 'too Much' Power For The Street?  

74 members have voted

You do not have permission to vote in this poll, or see the poll results. Please sign in or register to vote in this poll.

Recommended Posts

My 26 GTS4 with 280 odd kw is more then enough on the street - to the point were i haven't even touched the high boost setting

Mind you its running RWD at current so i take it half easy - and is the first Forced Induction car i have driven so of course it feels quick to me

The power im getting used to it....

Hard question to answer but id say even 200kw is more then enough

my gtr had 280rwkw, wasnt anywhere near enough.

all of it was usable on the street.

and I did at times.

well, overtaking anyway.

Varies - but I would say when the driver thinks it's a pain (pig) to drive in traffic. -> unrelated to kws/power <-

driver, clutch, gear box, gear ratio's, steering, suspension/set-up, brakes, tyres

but to provide some general indication due to the subject 100 to 400. (so I spose that's saying I think over 400 :wacko: )

Depending on the driver, vehicle and the destinations frequently travelled.

Edited by Sinista32

I reckon 300kw's is enough for the street, at street speeds its all about the low down torque, to me a VL turbo is/was the ultimate streeter, 3L's of good low down torque off the line with just the sound of the rb whistling thru the streets , riding the clutch for spool ups or frying second gear up a short stretch

speed-bumps-continuous_zps208577bc.jpg

^^ This is how Canberra is starting to look...

But as people are saying it's all down to the driver there is no such thing as too much power for the street.

I always thought 350kw would be "enough" but it wasn't and as I go higher in power level I still drive mine on street on a regular basis when I have it.

I can name four 1000hp Supra's running manual boxes that could be driven daily.

And a few V8's making 1000hp+ on the street with manuals.
Commodore going around with twins on it making 1200 rwhp, and he drives it everywhere no problem.

That being said, a turbo'd V8 has more low end than a Supra or Skyline.

AWD cars aren't usually modded to big power limits because A: More to Break.
And B: Name an AWD car other than a Lambo, or GTR that is capable of producing 1000hp. (Very few I'd assume).
The reason most 1000whp cars are RWD is because 99% of sports cars ARE Rear wheel drive.


Just throwing it out there.
But 500hp is plenty for street bragging rights.
And upwards of 1000 hp is a bit ridiculous, only if you go to the drags every week is it worth it, other wise it's mostly a wank factor IMO.
I'll just be happy cruising in a 280awkw GTR...

LOL.
Too scared to break it. :-\

Too much power is when it puts you into a pole before you can react.

No, that is being irresponsible on the street! Nothing to do with power... With some of the drivers on the road these days i am sure there are people in camper vans capable of this!

A twin turbo commy would be pretty awesome, and unique mainly.

But, a GT-T is a RWD, so that would be better to run 1000hp then a GTR AWD?

Also, i could imagine modifying a GT-T to a twin turbo would be excellent fun, said no one ever.-.-

A twin turbo commy would be pretty awesome, and unique mainly.

But, a GT-T is a RWD, so that would be better to run 1000hp then a GTR AWD?

Also, i could imagine modifying a GT-T to a twin turbo would be excellent fun, said no one ever.-.-

:blink:

Why would you want a twin turbo GT-T? Well in that case it would be a GT-TT lol...... In saying that it has been done more than once on this forum and was no advantage over the single!

I think this thread has been full of opinions and personal beliefs on a question that is really not going to get a correct answer.

DO your research and learn what cars can and cant do, the 1000hp number gets thrown around a lot but very few will ever get there in a street car as there is no point! That and the fact that to do it Legally is impossible as far as i am aware!

Twin turbo commy would just make a shitty car, expensive!

  • Like 1

:rofl:

Its not easy for a 2.5 6 pot either...

34geteetee makes 391rwkw on 28PSI, whereas not only is Scotty's stagea running 4PSI more, but makes 50rwkw less despite running the equivalent turbo and displacement (2.5 6 pot)

Sometimes its not about displacement or cylinders, but more so engine design, the RB2.5 motor is certainly capable of huge numbers with head work and a built motor, but once again irrelevant for street use

34geteetee makes 391rwkw on 28PSI, whereas not only is Scotty's stagea running 4PSI more, but makes 50rwkw less despite running the equivalent turbo and displacement (2.5 6 pot)

Sometimes its not about displacement or cylinders, but more so engine design, the RB2.5 motor is certainly capable of huge numbers with head work and a built motor, but once again irrelevant for street use

I don't have a built motor or head work? Actually I don't even have an aftermarket headgasket so u fail to see how they contribute to big numbers?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
×
×
  • Create New...