Jump to content
SAU Community

Recommended Posts

I am very impressed by your work.

Considering the extent of work involved the idea of doing the design and initial fabrication work on the old rusted sedan shell before final fabrication in the hatchback shell is a great idea.

I will be following your build with interest.

In one page it's quite clear that your fabrication skills are brilliant!

This will be one polished car when it's finished. There'll be nothing slapped together about it. The engineer will have no other option but to pass it just because it's a whole lot of awesome!

This is gunna be one sick 'Rana!

Thanks guys for the positive comments, I wasn't sure how it would be received..

Here's a few details on what it will be running. The RB30 is from a Nissan patrol so they were a carburetted non catalytic converter engine, so I have told

the engineer I am fitting an "after market" fuel injection system and turbo, because I only need to comply to the emissions of the patrol motor the engineer

is letting me run any ecu and turbo but I have to run a cat. The motor will be built by JPC who I used to build in my other rb30 torana.

Ecu will most likely be another vipec v88, the awd system will be run by Full Race's ETS-pro if I hadn't come across this system I probably wouldn't

started the build. Brakes are R33 Brembos, the rear end is R33 gtr, front is R32 and using BC coilover. From the outside it will look like just a

LX hatchback in mandarin red but the difference will be this one will actually go, stop and turn. The last photos are where the build is at, it will probably

take 2 years to finish, so it will be a slow build and maybe a few weeks between posts.

Thanks Glen

Here's a couple of photos of my other torana.


IMGP0599_resize.jpg
IMGP0600_resize.jpg

geeebuss!!!!!!!!!!! I'm not a Torana man but hell that is dedication and definitely a unique build. What do you do for a crust if you don't mind me asking. You don't get nice welding skills like you have by being an accountant haha but then again if your a boily I couldn't imagine coming home and wanting to do it in your own time as well or am I thinking of how I would be.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...