Jump to content
SAU Community

Recommended Posts

  • Replies 96
  • Created
  • Last Reply

Top Posters In This Topic

I would go with Jem

Unless you get your whole build done at Powertune they won't look after you customer service is shit tune shit never again my brother got his car tuned there

First tune chea didn't even tune it someone else name Lui did

worse was on the print out it said s15 when it was a s13

said it made 240 odd kw

Ran very rich blew smoke laggy and couldn't even run a 12s at wsid 110mph power wasn't right old setup tuned by toshi 210rwkw ran that.

Smaller turbo std cams

Went for a retune but specifically asked Chea to tune it made only 220rwkw something this time round but drove better no smoke but low power

When I picked it up kenji said it made good power when it made less than before and for the mods it was very low and didnt even say or help guide me into what was wrong

My other brothers car tuned by Unigroup same setup bar cams made 250rwkw

This s13 tuned by Powertune made 220odd rwkw

Both had sr20det,bc cams springs,gt3071r,740cc injectors and z32afm

Usually at wsid 1/4 mile trap speeds

210rwkw - 110mph

230rwlw - 117mph

250rwkw - 121mph I've personally tested this

Yet the first tune at Powertune was only running 13.0 at 110mph and they said it made 240rwkw don't even think they tune it the first time

Spent almost $1000 got no where

Nope j.e.m only going to ring around Monday morning

Not that I am local, but I have been around here for a while and have seen only evidence of good work and equally important great attitude to customers from JEM and would be going to them if I were in that area.

And because 34GeeTeeTee haha

i use powertune.

first tune was excellent.

started and idled great.

ran very smoothly.

now a completely different set up.

have done run in tune.

a few issues arose, but were sorted.

going back for power tune when I have the cash.

ive had nothing but excellent customer service, and only good things to say.

I also built the car myself, so they havnt touched the mechanical.

also done the first mods myself.

talk to both.

both have a good overall reputation.

pm a couple of people on here with cars of similar setups, and ask where theirs were done.

get a feel for both.

also, in saying I use powertune, jem would be a close second for me.

either way good luck.

Its the same distance towing than driving :P. Im not far from you Luke and I take it to Jez.

It's all personal preference. Where you feel comfortable leaving your car, go with it. If they bugger up, don't go back. If they are good, you found your shop. Talk to as many shops as you can.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...