Jump to content
SAU Community

Recommended Posts

Horray! Success!!

The O2 sensor socket arrived yesterday so last night I got stuck into my Stagea 260RS and switched over the O2 sensors. After much swearing and 3 HOURS, the job was done.

I used NTK sensors that had the following number on the body OZA395-E2 KBA16693. They were ordered from Global EFI with part number 351-0040. Once the job was done, I stuck on Consult (at 12:30 at night) and watched the voltage of both sensors flick up and down like it should at cruise (before, 1 sensor was doing pretty much nothing). The car seemed to idle nicer (I have had idle problems since I bought it), but this could just be in my head. I'm waiting for my wife to tell me how it cold-started this morning.

I noticed the following things from this job:

-The stock sensors are Zirconia, not Titania. I can't confirm that the R33 GTR is identical to the 260RS, but I'm told this is the case.

-The leads on the new sensors were shorter than the old ones. This means I couldn't clip the lead onto all of the little guides, but at least they reached.

-The rear sensor has a rectangular plug that fitted perfectly. The front sensor had a square shaped plug that was different. It was an easy job to unpick the connectors from the new plug and re-use the old plug. This meant that I didn't need to join wires or anything nasty like that :P

-From what I've read in the past, I thought it was the rear sensor that had the square plug. Perhaps people are confused because the plugs that the O2 sensors go to are sat side by side. However, the front sensor goes to the rear plug and the rear sensor goes to the front plug!

So there you go... the Stagea 260RS (and possibly R33 GTR) take the same Zirconia sensors as the GTS-T and at $77 from Global EFI, you can't really go wrong :woot:

I'm very happy. Thanks heaps for all the advice guys.

Edited by BoostedBarge
Good to hear mate.

Does Global EFI have a website/mail order service? I need one for my subie.

I haven't seen a website or mail order (it would be nice). I just rang them. They are easy to deal with over the phone

Update on results: the idle problem still seems to be happening (prob unrelated). I took the car camping on the weeken up Mt Tamborine, which involved both highway driving and mountain roads (and occasional flogging). So far I got 240km out of half a tank. I think that's the best we've ever got. If I get more than 400km out of the tank, then I'll know the O2 sensors have made an improvement.

Edited by BoostedBarge
I haven't seen a website or mail order (it would be nice). I just rang them. They are easy to deal with over the phone

Update on results: the idle problem still seems to be happening (prob unrelated). I took the car camping on the weeken up Mt Tamborine, which involved both highway driving and mountain roads (and occasional flogging). So far I got 240km out of half a tank. I think that's the best we've ever got. If I get more than 400km out of the tank, then I'll know the O2 sensors have made an improvement.

Hi Boosted Barge

i am really keen to know if this has indeed improve mileage. i have a R33 GTR and for a full tank it only does 200 - 220 km with driving OFF boost. i tried to google Global EFI and didnt get related results, whats their tel #?

with this price i dont mind trying it out even if they dont work with GTR RB26DETT

Cheers

Hi Boosted Barge

i am really keen to know if this has indeed improve mileage. i have a R33 GTR and for a full tank it only does 200 - 220 km with driving OFF boost. i tried to google Global EFI and didnt get related results, whats their tel #?

with this price i dont mind trying it out even if they dont work with GTR RB26DETT

Cheers

That's terrible fuel efficiency. My Stagea 260RS has the same engine as yours, but lugs around an extra 200kg and I was getting 300-400km out of the tank before fitting the O2 sensors. So far, since fitting the sensors I've got 240km out of half a tank (half highway cruising, half mountain roads with the occasional flogging). Maybe something else is wrong. I'd suggest doing a fault code check or plugging COnsult into it (if you don't have Consult see if someone on the forum near you could lend it to you). THe number for GLobal EFI is 0755310055. There's a also a group-buy on O2 sensors going at the moment. I can't confirm if the group-buy sensors are identical to the ones sent to me from Global.

ok, i went to the effort of reading all 15 pages (and i'm a slow reader!) and i didn't find an answer to my question. i took my car to the garage the other day and asked about the whole o2 thing as i'm getting bollocks economy. anyhoo, the guy turned off the o2 sensor from my power fc to see if the economy improves. does this make sense? i wouldn't have thought the economy would go any better just because the sensors are turned off but i'm going to run through a tank first to see how it goes - so far looks the same though. this is a 32gtr btw. cheers guys - sorry to make this thread even longer!

That's terrible fuel efficiency. My Stagea 260RS has the same engine as yours, but lugs around an extra 200kg and I was getting 300-400km out of the tank before fitting the O2 sensors. So far, since fitting the sensors I've got 240km out of half a tank (half highway cruising, half mountain roads with the occasional flogging). Maybe something else is wrong. I'd suggest doing a fault code check or plugging COnsult into it (if you don't have Consult see if someone on the forum near you could lend it to you). THe number for GLobal EFI is 0755310055. There's a also a group-buy on O2 sensors going at the moment. I can't confirm if the group-buy sensors are identical to the ones sent to me from Global.

Thanks. i will take it to a place where they have Nissan consult to do a scan then, it might as well be. i had it only for two weeks and filled up two tanks already :) i had my 210rwkw gtst and it was doing good 350 - 370 per tank and thats with flooring on first second and third ;)

please do post(i know you will ) what you will get this time for a full tank.

cheers

ok, i went to the effort of reading all 15 pages (and i'm a slow reader!) and i didn't find an answer to my question. i took my car to the garage the other day and asked about the whole o2 thing as i'm getting bollocks economy. anyhoo, the guy turned off the o2 sensor from my power fc to see if the economy improves. does this make sense? i wouldn't have thought the economy would go any better just because the sensors are turned off but i'm going to run through a tank first to see how it goes - so far looks the same though. this is a 32gtr btw. cheers guys - sorry to make this thread even longer!

Thats spot on mate, what the guy did is correct. when my gtst's O2 sensor gave up my tuning guy turned it off from Power Fc. it did more K/tank with O2 sensor off, best way to isolate the issue. i wish my new R33 had a apower FC :) well..

How do you do this? Is it only in datalogit or can you access this from the hand crontroller.

For those with large dia bosses for small dia sensors, I picked up a pair of adapters from the local exhaust mob for about $35, screwed straight in. Pity that one of my original sensors looks like it didn't like being removed and replaced, or was dead previously without me knowing.

slow reply but none the less. :wave:

The option is in the newer PFC's. From memory its in the Function select area. Where you turn on/off the option to use o2 feedback, boost controller etc.

It was a bit of a bugger. I paid $190 for a new o2 sensor only to have the tuner turn it off and leave it off. Economy is great regardless so I careless. :(

Changed my O2 sesor and could't be happier, I get an extra 100kms out of a tank now, fuel economy is 10 - 10.5 L / 100 kms for stockish r33 gtst. When I pulled the old one out, the insides looked all broken, no wonder it wasn't working, car has done 110k which is fair enough.

Everyone seems to be getting good results from changing o2 sensors!!

Ive just ordered mine from the good guys at kudos! hopefully it arrives this week sometime and ill wack it in on the weekend!

More fuel economy FTW

  • 2 weeks later...

i just bought an EL falcon 02 sensor from repco for $71.99, I made sure that the thread would fit the new dump pipe i'm installing.... My R33 gtst series 2 has 3 wires for the 02 sensor, 2 white and one black, and the new 02 sensor has 2 black and one blue. I am assuming that the blue wire on the new 02 sensor connects to the black wire on my car, and i supose it doesnt matter which other 2 wires are conected to which????? can somebody confirm this????

i just bought an EL falcon 02 sensor from repco for $71.99, I made sure that the thread would fit the new dump pipe i'm installing.... My R33 gtst series 2 has 3 wires for the 02 sensor, 2 white and one black, and the new 02 sensor has 2 black and one blue. I am assuming that the blue wire on the new 02 sensor connects to the black wire on my car, and i supose it doesnt matter which other 2 wires are conected to which????? can somebody confirm this????

why didnt u buy a nissan one? they are about the same price....

well these guys arnt much help lol.... to answer anyone else who has a question like mine in the future there should be 2 wires coloured the same as each other on the standard car wiring harness and one coloured another colour......

on the 02 sensor the colours may not match,,,,, but the will always (should always) have 2 wires coloured the same and one coloured different.

Connect the 1 odd coloured wire from the 02 sensor to the odd one out in the original harness.

then it doesnt matter about the other 2, just make sure both of the left over wires from the 02 sensor are connected to the other 2 wires of the original harnes. make sure they dont touch obviously

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yes correct. Also, I'd avoid applying it to soft paint (however I doubt you'll ever have to deal with it in practice). So any paint that hasn't fully hardened, could be a 1k paint that never fully hardened or it could be a 2k paint that was laid down thick and hasn't yet fully hardened. 
    • Bit of an update to this one. Having some issues on the dyno that held us back (boost spiking) and I want to pass some info over you guys and see what you think is wrong with my setup. The current readout on this dyno is 462rwkw on a low reading dyno so keep in mind it is a real world 500rwkw setup on a hub dyno. Don't read into the power figure too much as a sign of the issue. The short and curly of it is: 2.8 Litre Racepace build RB25 NEO N/A Head with VCT (internally standard however ) Borgwarner EFR 8474  Turbosmart 50mm Straight Gate + Mac valve 6Boost Manifold 4" dump to full 4" exhaust (nil restrictions) Wastegate plumbed back in and all angles in the exhaust system are acceptable and not too sharp. GFB SV52 BOV in cooler piping  Turbosmart BOV in EFR Housing   The issue we are having is it comes onto full boost for example at 4000rpm and spikes to 24/25psi, before dropping down to 17psi before slowly rising back up to the target boost of 23psi. It was extremely uncontrollable and the tuner actually had to ramp in boost progrssively with each 1000rpm on each boost setting we selected to try and reduce the amount of spiking. Sometimes we would see a drop of 10psi from the peak at the beginning of the run, to the low, until it took the next 500-1000rpm to stabilise back up to the target boost. The tuner is pretty confident that the straight gate is just a poorly designed product and leaks too much boost upon cracking the gate open and theres no way to fix it other than going to a poppet valve. He's also confient theres no ignition breakdown or floating valves. The fueling is extremely stable as well. Turbo speed is somewhere around the 109,000rpm area. The spanner in the works for me is that prior to this Borgwarner and StraightGate, the car was tuned on -5 twins at a diferent tuner, and he also had issues controlling the boost with it spiking around the same rpm range, so to me this sounds like the same issue and it can't be anything on the turbo side as this was all changed and I think the behaviour is extremely similar, if not the same. We also removed the mac valve and did a run on wastegate pressure and it still spiked and had the same behaviour. My thoughts on possibilities are: Boost Leak VCT Cam Gear isn't reliably activating consistently - (On this however, we did a run with the VCT disabled and the boost still spiked) Turbosmart BOV is not handling the boost? However this seems unlikely to not be able to handle 20psi. I have a couple of logs that I can't make sense of if anybody knows how to read them and can obtain further logs of other parameters if they are not enough, happy to pay for anyones time. The dyno readout with the power figure is the most recent last week. The other picture is from two weeks prior to that where we couldn't break 400kw (we removed the cat), however the issue of the boost control persisted. @Lithium @Piggaz @burn4005 @GTSBoy @discopotato03 I've tagged those that were quite active in recent pages here, no disrespect to those that know turbos well but I missed tagging. Cheers 
    • I recently purchased a 2018 Infiniti Q60, which has an SD card navigation map. I can see my system has options for real time traffic updates etc, and am wondering if there is something I can purchase to get this working? I can see there are at least updated maps for USA and Canada, but nothing for Australia. Surely Infiniti took changing road systems and city expansions into account when they decided to use an inbuilt navigation over Android Auto/Apple Car Play, or are we doomed to drive on streets that don't exist in the navigation system if you drive to a new area?
    • Luckily I didn't put in etch primer as I just found out it's not compatible with my body filler lol. Also just need to sand the panel anywhere between 150-400 grit so I'm in the clear there. It does say to not apply to soft old paint, I assume that means paint that is flaking, peeling,etc
×
×
  • Create New...