Jump to content
SAU Community

Recommended Posts

  • 4 weeks later...

Hey I plugged in my consult today and the o2 sensor plays around at .70 to .80 volts, is it busted, could that be why I'm only getting 200kms to a tank, if so where's the best place to get a brand new one, there's no point in getting a second hand, thanks.

im looking at replacing my 02 sensor that is attached to the dump pipe and i came across this one on ebay what are peoples thoughts on it link is pasted below

http://www.ebay.com.au/itm/NEW-Nissan-R33-Skyline-NX-NX-R-N14-N15-Pulsar-O2-Sensor-/150632217769?pt=AU_Car_Parts_Accessories&hash=item2312613ca9

  • 3 weeks later...

I bought an aftermarket one off kudos motorsports which plugs straight in (highly recommended trader)

Didn't really improve my fuel economy but i do 90% city driving. I wonder whether the geniune item which is double the price can do a better job...

I bought an aftermarket one off kudos motorsports which plugs straight in (highly recommended trader)

Didn't really improve my fuel economy but i do 90% city driving. I wonder whether the geniune item which is double the price can do a better job...

It either works or it doesn't there isn't much to them. If it is working then buying another working one will produce basically identical results.

  • 3 weeks later...

Fellas:

100% confirmed that NGK / NTK part no: OZA395-E2 can fit in an r34 GT-T and does work.

100% confirmed the plug DOESN'T FIT, however the switch is extremely simple.

im getting MUCH better fuel economy since installing the Zirconia 3-Wire, 22mm O2 sensor for the 32 / 33.

stop paying $220 for the original one!!!

Tim

  • 3 weeks later...

Installed Power FC - doing basic setup for a tune as suggested in the Power FC FAQ.

Whenever I put it into closed loop mode it starts to idle really rough, A/F goes very rich on my wideband (12:1), and it barely drives. If I take it out of closed loop it runs richer than standard ECU but idles and drives normally.

I know closed loop relies on the oxygen sensor to trim fuel at steady accelerator levels - so does the above indicate it is stuffed? I did a sensor check at idle through the hand coontroller and it sat at 1.3 V. i revved it and it didn't change? Is it time for a new one?

Thanks,

Pete

Installed Power FC - doing basic setup for a tune as suggested in the Power FC FAQ.

Whenever I put it into closed loop mode it starts to idle really rough, A/F goes very rich on my wideband (12:1), and it barely drives. If I take it out of closed loop it runs richer than standard ECU but idles and drives normally.

I know closed loop relies on the oxygen sensor to trim fuel at steady accelerator levels - so does the above indicate it is stuffed? I did a sensor check at idle through the hand coontroller and it sat at 1.3 V. i revved it and it didn't change? Is it time for a new one?

Thanks,

Pete

yes

you may also be able to run a simulated output from your wideband to the ecu

Cool - thanks mate! I'll read the wideband manual regarding the simulated output function.

Also, does anyone know how the cheaper NGK ones compare to the more expensive OEM Nissan ones? I checked them both out on Kudos' site.

Thanks again!

**SORRY for the double post - didn't think the stupid phone uploaded the first one!**

Edited by Peter

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...