Jump to content
SAU Community

Recommended Posts

Just built a new house and want to seal the floor of the garage.

so many different products out there i would like to know whats best? i spill oil water etc when working on cars.

i seen in this section many photos of cars sitting on nice clean garage floors

If you can afford to, do a polyurethane or epoxy type floor seal. This is nothing like hardware store floor sealer.

These surfaces are used in industrial high traffic areas, the food factories I've worked in renew them every 5 years or so; as a home garage floor it would be next to indestructible.

You can steam clean, no damage, use jacks etc, no problem. They can be textured or a gloss finish; the gloss is like glass.

get onto http://www.garagejournal.com/forum/ it's basically SAU but for garages / workshops & is quite frankly awesome. Has a whole section on Flooring.

Then recommend getting into the 'garage gallery' section which is basically build threads. Current favourites are The Concrete Underground, 44 Bikes Frame Shop & Mark's Monster Garage but seriously heaps of awesome builds.

Prepare to lose hours / days / weeks...

The epoxy flooring is tough, but certainly not indestructible. I have 2 garage floors done in this stuff (total about 240m2) and if you drop sharp steel objects on it hard enough it will damage the coating. I just finished fabricating a heap of shelving and work benches and dragging 100kg shelf units across the floor (with sharp edges on the end of the feet) does scratch / damage the surface. If you drop something heavy onto the concrete, it'll crumble the concrete underneath and the poly coating will come off.

Still, this stuff is infinitely stronger than paint, so will stand up to general wear and tear (dragging jacks across the floor, pressure washing, oil spills etc.)

Also remember some of it is very slippery when wet.

I used paving/concrete paint from bunnings, and it is starting to wear after only 12 months of weekend use. So depending on price of the epoxy stuff I would go that instead. It still looks good overall and seals oil/water properly but I don't think its going to last as long as I'd like.

Most workshops that use paint redo it every year.

Also it's important to acid etch the floor first or it will flake off early.

Shit, that garage forum will have me stuck for hours!

it seems poly or epoxy is the way to go. bout 499 for 20L which should do my floor and my old mans also tho his will need a fair bit of cleaning or diamond cutting back since its over 10 years old and is fairly worn. both about 6x6m

Shit, that garage forum will have me stuck for hours!

it seems poly or epoxy is the way to go. bout 499 for 20L which should do my floor and my old mans also tho his will need a fair bit of cleaning or diamond cutting back since its over 10 years old and is fairly worn. both about 6x6m

You want a rough surface for the paint to stick to. It mechanically adheres to the concrete it doesnt react with it. So clean it, degrease it and etch it with either the proper etching stuff or if you know what you are doing and are careful (fkn careful) acid.

  • 1 month later...

so i've done the clean, and sand of the garage floor. @$#%^^$# asian painters and plasterers that did my house are a bunch of messy %@$$^#$%&$%^$%

Did the etch on wednesday afternoon and have now got the first layer of epoxy down its starting to look pretty good. except for the small cracks everywhere.

will grab a photo today after the second coat. i ended up buying the epoxy from csw coatings 10L kit will do two pretty thick coats on my 6x6 m2 floor.

How much was the 10L? I've got a 6X7 garage and 14X8 shed to do, both new concrete.

Would you still need to etch clean a brand new floor? Obviously clean off the concrete dust and give it a good wash but would it need an etch?

Amerlock 400 is the go

My garage is done in this. After looking at dads shed, about 15 years its had the stuff on it and we have dragged, dropped, got thiners, oil etc on it and the only bit that has been damaged is missing a chunk of concrete. The stuff is great

We got it locally at an industrial paint etc supplier, can't remember how much but about 10L did the garage floor, the small shed slab and a little bit of concrete where my small clothes line is. Will try and get a photo in a bit

How much was the 10L? I've got a 6X7 garage and 14X8 shed to do, both new concrete.

Would you still need to etch clean a brand new floor? Obviously clean off the concrete dust and give it a good wash but would it need an etch?

bout 300 i think i spent. acid, masks, paint rollers and metal paint pole + other shit

i had to sand my floor in many places, and get the high pressure hose on it , and yep etch is a must unless you grind.

i mixed half the 10l bucket and did two coats for 6x6 and had enough left over to do a fair bit more so a 20L would get you done with two coats.

post-31456-0-28551300-1385110007_thumb.jpg

Would anything like this be OK? Or not worth the bother? Not cheap by any means.
I just need to paint half the concrete floor of a double garage.

http://www.bunnings.com.au/berger-jet-dry-10l-heavy-duty-evening-stone-paving-paint_p1410009

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...