Jump to content
SAU Community

Recommended Posts

Just built a new house and want to seal the floor of the garage.

so many different products out there i would like to know whats best? i spill oil water etc when working on cars.

i seen in this section many photos of cars sitting on nice clean garage floors

If you can afford to, do a polyurethane or epoxy type floor seal. This is nothing like hardware store floor sealer.

These surfaces are used in industrial high traffic areas, the food factories I've worked in renew them every 5 years or so; as a home garage floor it would be next to indestructible.

You can steam clean, no damage, use jacks etc, no problem. They can be textured or a gloss finish; the gloss is like glass.

get onto http://www.garagejournal.com/forum/ it's basically SAU but for garages / workshops & is quite frankly awesome. Has a whole section on Flooring.

Then recommend getting into the 'garage gallery' section which is basically build threads. Current favourites are The Concrete Underground, 44 Bikes Frame Shop & Mark's Monster Garage but seriously heaps of awesome builds.

Prepare to lose hours / days / weeks...

The epoxy flooring is tough, but certainly not indestructible. I have 2 garage floors done in this stuff (total about 240m2) and if you drop sharp steel objects on it hard enough it will damage the coating. I just finished fabricating a heap of shelving and work benches and dragging 100kg shelf units across the floor (with sharp edges on the end of the feet) does scratch / damage the surface. If you drop something heavy onto the concrete, it'll crumble the concrete underneath and the poly coating will come off.

Still, this stuff is infinitely stronger than paint, so will stand up to general wear and tear (dragging jacks across the floor, pressure washing, oil spills etc.)

Also remember some of it is very slippery when wet.

I used paving/concrete paint from bunnings, and it is starting to wear after only 12 months of weekend use. So depending on price of the epoxy stuff I would go that instead. It still looks good overall and seals oil/water properly but I don't think its going to last as long as I'd like.

Most workshops that use paint redo it every year.

Also it's important to acid etch the floor first or it will flake off early.

Shit, that garage forum will have me stuck for hours!

it seems poly or epoxy is the way to go. bout 499 for 20L which should do my floor and my old mans also tho his will need a fair bit of cleaning or diamond cutting back since its over 10 years old and is fairly worn. both about 6x6m

Shit, that garage forum will have me stuck for hours!

it seems poly or epoxy is the way to go. bout 499 for 20L which should do my floor and my old mans also tho his will need a fair bit of cleaning or diamond cutting back since its over 10 years old and is fairly worn. both about 6x6m

You want a rough surface for the paint to stick to. It mechanically adheres to the concrete it doesnt react with it. So clean it, degrease it and etch it with either the proper etching stuff or if you know what you are doing and are careful (fkn careful) acid.

  • 1 month later...

so i've done the clean, and sand of the garage floor. @$#%^^$# asian painters and plasterers that did my house are a bunch of messy %@$$^#$%&$%^$%

Did the etch on wednesday afternoon and have now got the first layer of epoxy down its starting to look pretty good. except for the small cracks everywhere.

will grab a photo today after the second coat. i ended up buying the epoxy from csw coatings 10L kit will do two pretty thick coats on my 6x6 m2 floor.

How much was the 10L? I've got a 6X7 garage and 14X8 shed to do, both new concrete.

Would you still need to etch clean a brand new floor? Obviously clean off the concrete dust and give it a good wash but would it need an etch?

Amerlock 400 is the go

My garage is done in this. After looking at dads shed, about 15 years its had the stuff on it and we have dragged, dropped, got thiners, oil etc on it and the only bit that has been damaged is missing a chunk of concrete. The stuff is great

We got it locally at an industrial paint etc supplier, can't remember how much but about 10L did the garage floor, the small shed slab and a little bit of concrete where my small clothes line is. Will try and get a photo in a bit

How much was the 10L? I've got a 6X7 garage and 14X8 shed to do, both new concrete.

Would you still need to etch clean a brand new floor? Obviously clean off the concrete dust and give it a good wash but would it need an etch?

bout 300 i think i spent. acid, masks, paint rollers and metal paint pole + other shit

i had to sand my floor in many places, and get the high pressure hose on it , and yep etch is a must unless you grind.

i mixed half the 10l bucket and did two coats for 6x6 and had enough left over to do a fair bit more so a 20L would get you done with two coats.

post-31456-0-28551300-1385110007_thumb.jpg

Would anything like this be OK? Or not worth the bother? Not cheap by any means.
I just need to paint half the concrete floor of a double garage.

http://www.bunnings.com.au/berger-jet-dry-10l-heavy-duty-evening-stone-paving-paint_p1410009

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
    • What ECU are you running? This is probably the biggest question. If it's a PowerFC, I'd probably change the ECU and get something newer that will handle the injectors in a nicer way.
×
×
  • Create New...