Jump to content
SAU Community

Recommended Posts

I get on average 260Kms a tank with my GTT aswell. Engine wise it's completely stock. I've cleaned AFM changed the fuel filter, fuel filter was completely clogged I noticed a slight difference in fuel consumption, maybe I'll have to go for the O2 sensor and new plugs see if that helps as well

Also if someone has put a low temp thermostat in, or yours is stuck open, then that will also add to poor fuel efficiency. Cold crank enrichment tapers off at 70C so the quicker she gets up to temp the better.

This. I put a Nismo thermostat in my Riceline, water temp now sits at 60C unless I'm at a track day. I struggle to get 12L/100kms, when I first bought the car I easily got 9.5L/100kms on the highway

I do do alot of short trips, I'm running PFR8 plugs with a 0.9 gapp,

Short trips, incorrect heat range plugs - no wonder you have absolute crap economy.

Try running a 6 heat range for starters. And plan your trips better so the engine operates at the correct temperature for most of the time.

So OEM/stock thermostat is best for fuel economy? What about oil cooler with built-in thermostat?

Mines got a oil cooler with no thermostat, oil temp sits between 70-80 degrees. I run BCPR6ES plugs with the standard gap, which is 0.8mm from memory.

I've found V Power to give me greater mileage than BP Ultimate for some reason too

I ran those before the PFR8S and it was the same thing, well the owner in Japan did fit quite a few Nismo parts to the car, I'll check what thermostat is in there and give the AAC valve a clean aswell, is there a way I can get error codes through a power fc by any chance, thanks.

And whats the difference between the BCPR6ES and the BCPR6E? And could some refresh my mind the lower the number the higher the plug temp correct? thanks.

Edited by MrRx7s3

Yep lower number is hotter. Has anyone checked their timing? That would have an impact on economy. Also should be talking litres per 100 ks as too many variables with a 'tank' of fuel.

true but seriosuly when were talking a difference of 550km- 250km, i dont think brimmed vs filled is going to mean too much.

Its not the difference of how full, but how empty it is when you fill it. Accuracy of fuel gauge and how far you are willing to with the gauge below the E.

mine been tuned a while back after i re-did my fuel pump mod for battery voltage, crap economy, around 300km on full (72L tank IIRC), o2 sensors turned off, bcpr6es plugs, no leaky injectors, although i do short trips (10km) each way to work, low temp sender perhaps buggered?

mine been tuned a while back after i re-did my fuel pump mod for battery voltage, crap economy, around 300km on full (72L tank IIRC), o2 sensors turned off, bcpr6es plugs, no leaky injectors, although i do short trips (10km) each way to work, low temp sender perhaps buggered?

Install a wideband o2 and see what your car is doing. I've seen lazy tuners who don't even care too much about off boost injection maps and just rely purely on o2 closed loop to work out the mixtures.

I find mine is chewing up a fair bit of petrol as well. I've put some fuel injector cleaner in which should help, also going to replace the spark plugs and clean the AFM sensor to see if that makes a difference.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
×
×
  • Create New...