Jump to content
SAU Community

Recommended Posts

I get on average 260Kms a tank with my GTT aswell. Engine wise it's completely stock. I've cleaned AFM changed the fuel filter, fuel filter was completely clogged I noticed a slight difference in fuel consumption, maybe I'll have to go for the O2 sensor and new plugs see if that helps as well

Also if someone has put a low temp thermostat in, or yours is stuck open, then that will also add to poor fuel efficiency. Cold crank enrichment tapers off at 70C so the quicker she gets up to temp the better.

This. I put a Nismo thermostat in my Riceline, water temp now sits at 60C unless I'm at a track day. I struggle to get 12L/100kms, when I first bought the car I easily got 9.5L/100kms on the highway

I do do alot of short trips, I'm running PFR8 plugs with a 0.9 gapp,

Short trips, incorrect heat range plugs - no wonder you have absolute crap economy.

Try running a 6 heat range for starters. And plan your trips better so the engine operates at the correct temperature for most of the time.

So OEM/stock thermostat is best for fuel economy? What about oil cooler with built-in thermostat?

Mines got a oil cooler with no thermostat, oil temp sits between 70-80 degrees. I run BCPR6ES plugs with the standard gap, which is 0.8mm from memory.

I've found V Power to give me greater mileage than BP Ultimate for some reason too

I ran those before the PFR8S and it was the same thing, well the owner in Japan did fit quite a few Nismo parts to the car, I'll check what thermostat is in there and give the AAC valve a clean aswell, is there a way I can get error codes through a power fc by any chance, thanks.

And whats the difference between the BCPR6ES and the BCPR6E? And could some refresh my mind the lower the number the higher the plug temp correct? thanks.

Edited by MrRx7s3

Yep lower number is hotter. Has anyone checked their timing? That would have an impact on economy. Also should be talking litres per 100 ks as too many variables with a 'tank' of fuel.

true but seriosuly when were talking a difference of 550km- 250km, i dont think brimmed vs filled is going to mean too much.

Its not the difference of how full, but how empty it is when you fill it. Accuracy of fuel gauge and how far you are willing to with the gauge below the E.

mine been tuned a while back after i re-did my fuel pump mod for battery voltage, crap economy, around 300km on full (72L tank IIRC), o2 sensors turned off, bcpr6es plugs, no leaky injectors, although i do short trips (10km) each way to work, low temp sender perhaps buggered?

mine been tuned a while back after i re-did my fuel pump mod for battery voltage, crap economy, around 300km on full (72L tank IIRC), o2 sensors turned off, bcpr6es plugs, no leaky injectors, although i do short trips (10km) each way to work, low temp sender perhaps buggered?

Install a wideband o2 and see what your car is doing. I've seen lazy tuners who don't even care too much about off boost injection maps and just rely purely on o2 closed loop to work out the mixtures.

I find mine is chewing up a fair bit of petrol as well. I've put some fuel injector cleaner in which should help, also going to replace the spark plugs and clean the AFM sensor to see if that makes a difference.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...