Jump to content
SAU Community

Help'''''. R34 Rb25 Gearbox Into R32 4Door Gtst Factory Manual

DriftSquad

By DriftSquad,
in Engines & Forced Induction

 Share

Recommended Posts

DriftSquad Experienced

DriftSquad

Posted
Posted

Hey guys for those of you who have done this conversion . My r32 4 door mspec needed a new gearbox. I've got an r34 manual box and I can't seem to get the box in the tunnel it hits the top of the tunnel. What's the trick?

Or do I need to start bashing the tunnel?

I stopped for the night but would like to have another go in the morning.

Also I've installed an exedy hyper twin plate already to motor

HR32GTS 4DOOR Community Regular

HR32GTS 4DOOR

Posted
Posted

The twin plate makes it hard as you can't get the box close enough to the motor before it goes up even with a 20 box it's tricky with a twin. What you need to do is loosen the engine mounts, jack the front of the engine up and get someone else to push the back of the engine down. It's a pain but once the 25 box is in you probably won't have to take it out fro a while.

DriftSquad Experienced

DriftSquad

Posted
  • Author
Posted (edited)

Thanks I got the gearbox in by loosening the engine mounts and jacking the front of the motor up. Once I did that I had more then enough room. I can confirm that a factory manual r32 4 door skylines gearbox crossmember stamped "C" or "A" (they are identical) will not straight bolt up to the rb25 r34 gearbox in the standard position. I welded to bits of flat bar to the top and extended and drilled new holes. Works fine.

I did what most people have done and got the standard tail shaft and had the r33 yoke put on and I think it may be to short. You be the judge. I think it needed to be about 10-15 mm longer just less then an inch.

post-22485-0-08755400-1403342283_thumb.jpg

Edited by DriftSquad
HR32GTS 4DOOR Community Regular

HR32GTS 4DOOR

Posted
Posted

Yeah looks like whoever did your tailshaft made it to short. How did you get the tailshaft made up? Was it a tailshaft from a non abs or abs r32? are you using a abs or non abs diff?

DriftSquad Experienced

DriftSquad

Posted
  • Author
Posted (edited)

I'm not 100% if this car was abs or not.it is am m-spec factory manual sunroof ect

All that was done was the r33 yoke was welded to the standard r32 tail shaft. Many people on this forum said that was all it was needed so I was hoping some one could compair

Edited by DriftSquad
HR32GTS 4DOOR Community Regular

HR32GTS 4DOOR

Posted
Posted

That's all you need. Looks like it was cut down a little short. You could go get yourself an abs diff as the nose is a little longer (like 10-15mm), will push the tailshaft further into the gearbox. The centre bearing should have enough movement in it to allow this.

  • 6 years later...
toranarod Contributor

toranarod

Posted
Posted

R34 GTT Tail Shaft yoke for a manual gear box. 

Can you buy the yoke as a spare part for turbo GTT r34? Is the Auto yoke the same I suspect not?

Like most of us with an Auto R34 a manual conversion is on the to-do list. It seems like the gear box is buyable but all the other parts are harder to come buy especially the tail shaft. Oh and the gear stick.      

iruvyouskyrine Grand Master

iruvyouskyrine

Posted
Posted

Just ask for a new one when you are in a driveshaft shop asking them to make you a new driveshaft. Nissan dont have them buy any driveshaft place will be able to get them.

  • Like 1
Kinkstaah Grand Master

Kinkstaah

Posted
Posted
14 hours ago, toranarod said:

R34 GTT Tail Shaft yoke for a manual gear box. 

Can you buy the yoke as a spare part for turbo GTT r34? Is the Auto yoke the same I suspect not?

Like most of us with an Auto R34 a manual conversion is on the to-do list. It seems like the gear box is buyable but all the other parts are harder to come buy especially the tail shaft. Oh and the gear stick.      

I have a R34, and I did a manual conversion on it, with a R33 GTST Gearbox. You just need the front half of the tailshaft to suit the gearbox you are putting in.

But also as above, you may be surprised how cheap a custom driveshaft is. I've since put a LS into the car and needed 2! driveshafts made up (because I changed the gearbox... yet again) and it's been surprisingly little fuss on the driveshaft front.

Don't use a TR6060 though. Bad ratios.

Kinkstaah Grand Master

Kinkstaah

Posted
Posted
21 hours ago, GTSBoy said:

Which is when you then drop in the LS to suit the gear ratios.!

/sneaky.

Even if you do that, still bad ratios! (I have no idea what people were thinking here)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      boost source Size Garrett gt28 gen2

      By TurboTapin · Posted

      You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • QB6SAGR
      Battle of the broken skylines

      By QB6SAGR · Posted

      Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Rezz
      Spotted on the street....

      By Rezz · Posted

      Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...