Jump to content
SAU Community

Recommended Posts

I tried searching it but got no results :(

I have a R32 Gts-t just wondering what people use and what brand they find is best to cope with lock to lock and daily duties? I have a little play in the steering, so i checked the reservoir it is below empty by like 10mm so I'm guessing its time for a top up!

These are all full synth, so will last longer and be more boil resistant, which will be important if you track it.

Nissan certifications in brackets;

Nulon Synth ATF (C D J K) 66.50/4L = $16.60perL
Valvo Synth ATF (D J K) 49.95/5L = $10.00perL
Transmax Z ATF (D only) 76.50/4L = $19.10perL

I use the Valvo because its well priced.

Any autobarn can do the Nulon synthetic for $50 if you ask. ;)

I would be flushing it all out personally.

Never done PS flush, Got any links or anything to a DIY?

Thanks guys i'll head done to a shop and get one of them!

nothing wrong with the 10dollar castrol power steering fluid been using it in my drift car for years and holds up well considering how hard racks are worked in a drift car.

Never done PS flush, Got any links or anything to a DIY?

Thanks guys i'll head done to a shop and get one of them!

dis connect lines from reservior drain it all oout and if you want it out of the rack disconnect lines on rack and turn wheel a few times will get it all out of rack aswell.

nothing wrong with the 10dollar castrol power steering fluid been using it in my drift car for years and holds up well considering how hard racks are worked in a drift car.

Are you running a PS cooler? I have seen way too many PS pumps fail at the track due to overheating, hence why I run synthetic fluid, in the hope it will protect better at high temps.

Which is the best among these two?

Dextron 3 trans

Shell SPIRAX S4 TXM

Dextron 3 is a fluid specification, not a brand.

Are you running a PS cooler? I have seen way too many PS pumps fail at the track due to overheating, hence why I run synthetic fluid, in the hope it will protect better at high temps.

Dextron 3 is a fluid specification, not a brand.

yeah at the moment i have a cooler but even without cooler for 2years never had issues with pump still on my first one.

I use nulon stuff, bought 1l at supercheap and that was plenty for the whole system, no hicas and replaced my rack with a 33 rack. Also I used one that has a leak inhibitor in it, was around 10dollars

  • 3 years later...

Hey guys I'm having trouble finding castrol tranmax z.

Is castrol transmax multivehicle suitable and a better option than castrol regular ATF Dex III

https://www.castrol.com/en_au/australia/products/cars/automatic-transmission-fluids/transmax-multivehicle.html

1391677212132.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...