Jump to content
SAU Community

Return Flow Intercooler

Adham33

By Adham33,
in Victoria

 Share

Recommended Posts

Odium Grand Master

Odium

Posted
Posted

Honestly with that much power in mind, just get a cross flow and a forward facing plenum.

It'll make life a lot nicer when it comes to working on the car and its a lot simpler (less joins, fewer points of failure)

Odium Grand Master

Odium

Posted
Posted

I tell you know, if you're going to be getting 380rwkw out of a GTST, it's going to be FAR from legal and you'll have more than a few headaches with police. Effectively turning your car and $10,000 worth of mods into a garage queen.

Just get a crossflow and get Scotty_NM35 to fab you up a pipe which can bend around the bottom of the radiator and pop up into the engine bay... No holes needed.

Birds Grand Master

Birds

Posted
Posted

A big high flow turbo + E85 + Blitz return flow + factory airbox would keep you under the radar.

In the end police will always be able to find an ECU or injectors or boost controller if they want to look for them, which means anything over 170rwkw has the potential to get you found out. It's all about hiding it as well as you can. If you can keep the engine bay looking stock they won't have reason to look much further. I'd argue that any forward facing plenum is grounds to scrutinise the engine bay, versus a cooler that uses the factory piping.

Birds Grand Master

Birds

Posted
Posted

But some people say blitz return flow cooler won't handle 380rkws .can only handle 250rwks

Some people don't know

I'm doing 275 with mine on a conservative dyno and I don't think it's at its limits.

scotty nm35 Grand Master

scotty nm35

Posted
Posted

If you are in Vic, keep it all looking as stock as possible. You can still make the power using ethanol as a fuel instead of dino 98.

Either a good return flow or custom piping cross flow will do the job, no need for holes to be cut. ;)

Count Grantleyish Grand Master

Count Grantleyish

Posted
Posted

How can cops find out what ecu or injectors u got???

also i have a blitz return flow for sale if your interested :)

If cops that moody, they'll tear your car apart.

Count Grantleyish Grand Master

Count Grantleyish

Posted
Posted

don't they need a warrant or something for that? they not really allowed to pull out the interior trims are they?

Dunno what rock you've been living in, but cops are known to take kick panel out to see what ecu the car has and some cops know what colour injector caps of cars.

Welcome to Victoria.

Plus some cops doesn't even do that and decide to send you a EPA letter and let EPA do the work.

Birds Grand Master

Birds

Posted
Posted

They carry portable tool kits

Screwdriver to pop open / destroy your kick panel and look for ECU

Injectors are pretty obvious if you know the engine and certain Knox people know the standard RB25 colour is dark red/maroon

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      I am probably calling this too early but I think I found what part of my problem is. I have a couple of dents that are fairly close to each other and I tried to fix them individually. Recently I put one larger coat across all the dents and sanded it and for the first time ever it's all even except for the edge where the bare metal is, I just need to put some putty there. I'm ordering some better longer blocks that are more flexible. Other good news is that the other repairs on my panel are flat even with the guidecoat. It's these 2 dents which are an absolute c*nt l lol.
    • MBS206
      Steps to DIY sanding car back ready for respray....

      By MBS206 · Posted

      Murray will have better input, but I'd be going with less filler, and aimed at the low spots mainly, and hence won't need as much sanding, which then means get the guide coat on earlier. That's how I'd do it, BUT, I'm not a pro, I'm a DIY hack who will then get the shits halfway through, and have one spot awesomely repaired, and the other spots look like a 3 year old was left unsupervised with workshop tools...
    • timmy94
      GTX2867R GEN 2 NO OUTPUT FOR BOOST SOLENOID

      By timmy94 · Posted

      Where is the most common place to locate it? Disappointing that Garrett won’t make a fitting for it since they know everyone will use it
    • GTSBoy
      Looking for someone with a R34 front bar

      By GTSBoy · Posted

      That's the spirit.
    • GTSBoy
      R32 GTR Limp Mode?

      By GTSBoy · Posted

      A HICAS fault really should not cause the engine to go into limp mode. These cars are so old that the systems barely talk to one another. The thump might be the lockoff solenoid valve for the HICAS (the safety valve) getting closed, to lock the rear wheels "straight". I say "straight", because when my HICAS used to shit itself before I took off and nuked it from orbit, it would lock up with the rear wheels wildy non-straight and you'd need 45° of steering wheel to drive straight. Take off and nuke it from orbit. First step is to pull the smaller of the two plugs out of the HICAS CU. See if it stops misbehaving. You can also (whilst leaving it plugged in) try to get the HICAS CU into diagnostic mode by doing the pedal dance, or by connecting a CONSULT capable diagnostic reader into the car and seeing what it has to say for itself. Can't do either of these with it unplugged though. 1st gen HICAS is a ballache. I would do a complete delete. I did do a complete delete.
×
×
  • Create New...