Jump to content
SAU Community

Recommended Posts

OEM stuff is fine, though unless you need the gear urgently I'd shop around as I've never found these guys to be particularly competitive on pricing.

Well tbh i havnt looked around yet but under 400 for the full genuine kit with a water pump seems decent to me?

I reckon that's a pretty good deal mate, I had both the normal and N1 water pumps in my old 32, negligible difference in temp on the hand controller between the 2, and no problems with either

I've got a gates belt on the 34 at the moment, 30,000 on it so far with no dramas. Went with a standard water pump over the N1

I think the fact that it's all genuine would tie in well with your build too

clutch pivot ball is squeaking like crazy, got under the car to have a look.
being damn holiday i coudnt get to the shop to buy lube. what lube should i get? something heavy, heavier than wd40 i read.

also as you can see, for some reason i dont have a rubber boot on the fork. hoping its not full of shit i there but i cant be bothered pulling the box out if i dont have to.

anyway to the point, listen to this...make you cringe?? :)
what do you think, is it f**ked or will a lube be ok for a while?

Edited by GH05T
  • Like 1

also im assuming i just spray grease here and keep pressing the clutch unill it goes away, is this the contact point or is it the other side, i cant quite see.
i dont wanna be spraying grease on the clutch.
which looks like an exeedy by the purple

907a5c47-e6cc-4850-8138-c44a30f72fd9_zps


more questions, im trying to work out what bits my car has,
these look like old TEIN coilovers yes?
sorry the photos are shit as i dont have a hoist, just under the car.

20150403_173127_zpsblwwgugm.jpg20150403_172107_zpsefjvuu5m.jpg



Also im trying to work out if that is a small cat or if its just a decat pipe, is there an easy way to find out?
and these look like stock front pipes?

20150403_172228_zpstthml9ae.jpg

20150403_172918_zpstvwquiz5.jpg

20150403_172927_zpstmqhkonq.jpg

Not sure about the gearbox squeak

But they look like after market mild steel front pipes and a 3" stainless decaf like the just jap ones, had one on my old gtr but you won't know for sure till you check inside the cat

ok, looks like im gonna actually have to address the tires situation before i get the new wheels.
:dry:

20150403_172509_zpszqulpsdz.jpg

Im still blown away how the car can handle on this sort of shit.

oh yeah, then this happened.
all i can say is its kinda a tradition.

20150403_130421_zpsgcrc4bze.jpg


and just cos i like looking at my own car, some expert phone picks :)

20150328_191333_zpspeyuw3xr.jpg
IMG_20150328_133004_zpsin0svp8g.jpg

clutch squeek is sorted For now.

Took my C pillar out to see if it was repairable and its completely f**ked and fallen to bits, looks like ill finally have to buy another one. Grrr.

Now, how the f**k do I release the bottom clasps to release the back seat (bottom section.) Holding the wire loops On the floor close to the front.

tiny update

sick of the standard bent and generally not fitting numberplates.
was gonna get the xx black plates but they have gone to YY plates which look odd.

so ordered some custom plates which i always thought would suit a gtr.

20150410_125601_zpsbdezqipl.jpg

get it?

im not usually a fan of custom plates but i don't mind something that the very occasional person would get. plus they come in square rear and slim front and are black.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...