Jump to content
SAU Community

Recommended Posts

235708553.jpg

SAU-NSW Club Membership


What is Skylines Australia NSW Inc.(SAU NSW)?

We are the Nissan Skyline Enthusiasts’ Club. If you own one or just admire Skylines in general then we are the club for you. The club holds social and track events throughout the year.

How is the club (SAU NSW) different to the forums (SAU)?

The Club was formed by a group of like minded forum users. It uses the NSW Members’ area as one of the ways for members to communicate.

The forums and the club are entirely separate entities.

How do I become a member of Skylines Australia NSW (SAU NSW)?

Becoming a member is as easy as going to our online store and filling in the online form. Once you have sent the form, you can post in this thread on the forum, to let us know. Link to online store is http://store5191044.ecwid.com/#!/SAUNSW-1-year-financial-Membership/p/38550086/category=10151475

What does being a member entitle me to?

Well, if the prestige and knowledge that you are a part of Australia’s largest Skyline enthusiast group isn’t enough, then take a look at what else you receive:

*Discounts on entry to club events.

*SAU NSW is CAMS affiliated (the first Skyline club in Australia to do so, VIC is the other) entitling club members to apply for the appropriate licences to enter motor sport events.

You will receive a membership card, car sticker and lanyard when you join. You can attend and vote at the AGM and have a say in how your club is run.

What sort of events does Skylines Australia NSW hold?

The events that the club runs, and participates in, include:

*Track Days
*Skidpan Days
*Super Sprints
*Drag Meets
*Motorkhanas
*and most other forms of club level motor sport.

We also participate in varied social events such as BBQs, Cruises and any other activity where a bunch of people who share the love of the same set of taillights can gather.

Okay, so I have filled in the form and sent it off, what happens next?

Once we receive your membership form and payment, you are added to the SAU NSW Members section of the online forum, email list, etc. Your membership card, etc. will then be sent to you as well. Please allow up to 3 weeks for your membership package to arrive.

If I need to know what’s happening to my membership, where can I find out?

By posting in this thread on the forums or by visiting our website at www.saunsw.com.au

SAUNSW Bank details.

Bank - NAB
Branch - Marrickville
Account name - Skylines Australia NSW
BSB - 082 356
Account number - 546 393 766

Are there any club rules or guidelines I need to read over?
There sure are. Have a read of the Skylines Australia NSW Rules and Constitution attached below.

SkylinesAustraliaVer1-6.pdf

Link to comment
https://www.sau.com.au/forums/topic/457457-s-a-u-n-s-w-club-membership/
Share on other sites

  • 2 weeks later...
  • 4 weeks later...

Thanks for your payments everyone.

They have been received and are being processed.

Ravi, Mathew (GTofuS-T) is our Secretary & hence the exec in-charge of memberships now.

Edit: Efficient Secretary is efficient indeed. Beat me to it.

  • 2 weeks later...

Thanks Josh and Welcome!

Application has been received, definitely check out the Events section for upcoming events, in particular we have a meet & great coming up this Sunday.

Cheers,

Mathew

Thanks, unfortunately i can't make this Sunday, but will get along to some other meets soon

Thanks Josh and Welcome!

Application has been received, definitely check out the Events section for upcoming events, in particular we have a meet & great coming up this Sunday.

Cheers,

Mathew

No rush, but when will I get access to the members only section of the page?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...