Jump to content
SAU Community

Recommended Posts

Exhaust sits much nicer now. Wondering where you purchased your Magnaflow muffler from and how long it took to arrive.

The inside of my rear muffler is broken and looking to replace with a decent quality one once my car is back on the road.

Been playing with it an hour here and there every time I get a chance and have got a little done but haven't been able to finish it due to parts suppliers being closed

1E9C9126-438C-47F4-B50A-8E7518525C27.jpg As part of using the haltechs capabilities and bringing the sensors into this century, I decided to get rid of the original crank angle sensor and go to a crank trigger set up

3697FCDA-17CE-4EDF-B3FF-0715A6A1CAC7.jpg

Started looking like this

90940903-0A41-4E04-B136-C76EBEF5F77A.jpg 30-40mins later I had this

After a bit of measuring and cutting I was able to fit the crank sensor, not the cleanest cut but with the limited room it was the best I could do

5287DC7C-43D6-43FF-A5B4-EB1AC8C86403.jpg

14D19BCF-2508-4039-9E94-1A9E1A91A83F.jpg Then fitted the belt and the actual trigger

B57CB2F5-650C-4EB6-BEA8-02121717A449.jpg And the cover back on just clears everything nicely

A466BD0B-A79C-4443-86FD-3DDA3107525D.jpg Top cover back on with the cam trigger fitted, still need to do the wiring but am waiting for my 3pin connectors to arrive.

Also as a side note I had a 500hp ati blanacer sitting around and it will not fit with this kit and either will the factory balancer. So am going to buy the big ati balancer when then suppliers open back up and try that

  • Like 1

It's not the wheel, it's the bracket that holds the sensor sits proud and the edge of the balancer lines up with it and won't allow the balancer to go all the way home

The bit circled in red is where is hits

F5983C83-032B-4222-893B-C3B25B8ED3D1.jpg

  • 1 month later...

Finally got a chance to work on it today and got the crank trigger all wired up and working through the ecu

Here's what it now looks like

0BFDC9C4-D096-48AC-B750-97B4532BB7FC.jpg

Next will be to fit this little puppy

9627C16E-C0FE-4E97-B92C-7FD4DF0A2AA1.jpg

  • 2 weeks later...

Been a bit slack with the updates but time hasn't really been on my side either,

I got all the interior back in and everything looks as per factory apart from 2 little bumps under the carpet against the sill

Got the ecu to recognize the flex sensor and wideband sensor but haven't enabled them as I will leave that for jez when the car is dropped off to him.

Fitted and wired the 3 bar map sensor but once again I will let jez enable that and hook up the hose, just cause the on board one needs to be disabled at the same time.

2F1C67B6-31BF-4ECF-86A4-06D765C3EF73.jpg

Also went to the local United and grabbed 80L of car God juice

90732F3F-BB5D-4829-8CD1-879B452A046D.jpg

Am proud of the sti as it fits 4 jerry cans with space to spare

F17A0917-D127-4752-B373-FB49B6645231.jpg

I just gave it a very over due wash and tomorrow morning it's booked in for a wheel alignment to fix up the castor after installing the rods, then straight up to jez for touch up and then enable the flex fuel to see what these little turbos can do

  • 2 weeks later...

Tuning has started and one of the first things jez noticed is how smooth the rpm signal is with the crank trigger set up

4D97145D-5142-40CE-8E07-15744F78D093.jpg

The blue line is the rpm signal and there is no wave in it what so ever

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
×
×
  • Create New...