Jump to content
SAU Community

Recommended Posts

y'all can have your shares and $800k investments, all i need is an income that can support me and help fund the wanky-est of VIP accessories. you could have a multi-million dollar car, but it wont have a slot for medium or large maccas chips or croc-skin benches to rest your sunnies. 

http://www.garson.co.jp/english/interior_i/e_potato_h.html

 

Swarovski-approved colour diamonds encrusted into just about everything. car rubbish bins, seat covers, dash mats, gear knobs, licence plate surrounds, valve caps. and just like Junction Produce, to become a distributor for their products you need to "buy" into the company first (Junction Produce is like somewhere between $5k-15kUSD).

On 08/07/2016 at 2:31 PM, Leroy Peterson said:

y'all can have your shares and $800k investments, all i need is an income that can support me and help fund the wanky-est of VIP accessories. you could have a multi-million dollar car, but it wont have a slot for medium or large maccas chips or croc-skin benches to rest your sunnies. 

http://www.garson.co.jp/english/interior_i/e_potato_h.html

 

Swarovski-approved colour diamonds encrusted into just about everything. car rubbish bins, seat covers, dash mats, gear knobs, licence plate surrounds, valve caps. and just like Junction Produce, to become a distributor for their products you need to "buy" into the company first (Junction Produce is like somewhere between $5k-15kUSD).

1849109365_569a41f236_z.jpg?zz=1

  • Like 1
On 7/9/2016 at 9:47 AM, UNR33L said:

 

yer cops over there are f**ked, killed over 500 people this year alone..

And how many of these are people who have pulled weapons on cops? probably >90%...

So, is it the cops fault they needed to defend themselves to stay alive and make it home? Or is it the 'victims' fault for pulling a weapon, or doing something stupid (like suddenly reaching into their pocket or waistband) that made it look like they were pulling a weapon?

If they want to stop getting shot by police, they need to stop carrying weapons and pulling them out all the time because someone looked the wrong way at them...

  • Like 1

That^

American cops might have shot 500 people but they also lost something like 30 of their own this year already.

Cultural issue but they will never get rid of guns. Too many people with a "just try and take my guns off me" attitude towards life. The irony being that the guns are supposed to be protecting them; instead inciting civil wars because people don't know how to use/carry them safely.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...