Jump to content
SAU Community

Recommended Posts

A sensible setup. 250-300kw is really the perfect setup for the 25, not so much that its unusable without jail time and sensible enough that you can still use it normally without it being a complete pig.

My evo 7 had a 3082 with a 1.06 rear on it, it was a complete dog below 4 and didn't hit full boost until 5.5. Ridiculous turbo choice by the previous owner, hilarious and fun but ridiculous none the less.

Was much better when I changed it to a high flowed stock turbo, was all on at 3500 and made almost the same power.

Mid size high flows are the way to go - improve a vehicle's power decently and leave it at that for reliability, tractability and usability.

When choosing my turbo I drove Hypergear's 340kw 33 that took until 4500rpm to actually get anywhere and then it wanted to eat a gutter. He asked me if I liked the power...I said no man, make me a turbo that comes on quickly instead of this, so he did. Haven't looked back - convinced my turbo is what these cars should have come with from factory!

There is more to performance than dyno charts

I just said centrifugal chargers have their benefits which aren't immediately apparent.

Midrange kick is pointless if you are breaking traction there. Seperating your stuff from being tied to your exhaust manifold is also nice.

The smart answer if modding a RWD skyline for power is immediately LS convert it.

26 minutes ago, Kinkstaah said:

There is more to performance than dyno charts

I just said centrifugal chargers have their benefits which aren't immediately apparent.

Midrange kick is pointless if you are breaking traction there. Seperating your stuff from being tied to your exhaust manifold is also nice.

The smart answer if modding a RWD skyline for power is immediately LS convert it.

Does it ever bother you that there are absolute f**kwits out there who wouldn't know a tenth of what you do about cars, driving 500kw GTRs up and down bypass that never miss a beat

  • Like 2
9 hours ago, Birds said:

Mid size high flows are the way to go - improve a vehicle's power decently and leave it at that for reliability, tractability and usability.

When choosing my turbo I drove Hypergear's 340kw 33 that took until 4500rpm to actually get anywhere and then it wanted to eat a gutter. He asked me if I liked the power...I said no man, make me a turbo that comes on quickly instead of this, so he did. Haven't looked back - convinced my turbo is what these cars should have come with from factory!

I must agree since i also have a highflow. aka - best skyline turbo ever, lol.

7 minutes ago, UNR33L said:

But I wouldn't want a 250km range or cold start issues :P

300km thank you very much. No cold start issues here, even on freezing cold mornings. Getting the cold start crank and post crank settings right is the key to cold starts on e85. Flex fuel = best of both worlds.

9 hours ago, Birds said:

Does it ever bother you that there are absolute f**kwits out there who wouldn't know a tenth of what you do about cars, driving 500kw GTRs up and down bypass that never miss a beat

I live right next to Glenny Kebabs and I hate this quite a bit at times :P (so many stanced golf R's holy shit)
I originally wanted to buy a Supra and could have, back in the day.
Would have done a lot more driving I assume, but wouldn't have (needed to) learn anything at all.
There is an element of fun to learning stuff, and there's always more stuff to break learn from

Only problem with E85 is that it allows you to push so hard on the tune you will break the next thing up the chain as it will never ping.

This ain't so good if you have metal head gaskets, head studs, stronger pistons, rods, crank because when they aren't the weakest point you end up Gregging it™

98 isn't a bad idea as it stops you from going too insane, its a built in safety measure of sorts to make sure the rest of your setup is actually going well. E85 is like fuel-steroids. You can get the 'right' power on 98 in a Skyline at least to the point where everything else starts to become a limitation. You may not get forum and instagram #efame but you will be able to have fun with the vehicle and have a modicum of reliability and do more than hardpark it and fap over a dyno sheet if you go full retard with timing. (or full advance on timing, really)

50 minutes ago, admS15 said:

300km thank you very much. No cold start issues here, even on freezing cold mornings. Getting the cold start crank and post crank settings right is the key to cold starts on e85. Flex fuel = best of both worlds.

Yeah flex seems like a good idea on paper, I'd want to have complete confidence in the tuner though! 

I think an STI would be more like 250km, those tanks are small af. Been looking into getting a Subi

Edited by UNR33L
1 hour ago, Kinkstaah said:

This ain't so good if you have metal head gaskets, head studs, stronger pistons, rods, crank because when they aren't the weakest point you end up Gregging it™

Going to remain silent on the Gregging it™ front, as the last track day that we were at together didn't end well for me and you came out unscathed

34 minutes ago, Odium said:

Going to remain silent on the Gregging it™ front, as the last track day that we were at together didn't end well for me and you came out unscathed

Whaaaa? What happen?

Everyone I was with that day was super happy they could lend the helmet you offered. You're the shining pinnacle of "Track day people are awesome!!" in their eyes. I did not know things went badly. Please tell me you didn't split a block due to aggressive timing due to magic E85 :P

2 hours ago, UNR33L said:

Yeah flex seems like a good idea on paper, I'd want to have complete confidence in the tuner though! 

I think an STI would be more like 250km, those tanks are small af. Been looking into getting a Subi

For me, it's been just as good in practice as it has been on paper. As far as the tuner, you'd want to have confidence in a tuner doing anything to your car even if it's not e85 related. Since going e85, ive had no issues to speak of. I run a tank of 98 every 3-4 months, followed by a change of fuel filter. Has worked well so far. I also drive my car daily, so the fuel never gets enough time to absorb water and turn things to shit. Knock on wood that by saying that i wont be in the gregging it(tm) club.

1 hour ago, Kinkstaah said:

Whaaaa? What happen?

Boost or Intake leak = overboosting turbo (correct psi by the time it got to the engine) = overheated turbo = warped / cracked exhaust manifold. My day was over by midday.

No worries about the helmet, never put blocks in place that stop people from getting out onto the track. We've got future track day participants to take care of!


Edit: 

 

88e positive news from update = up it goes, tomorrow back down again 

Give it till the 22nd for results... At the moment its happy building solid base, im happy it hasnt gone spastic high and then everyone dumps within 24hours.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...