Jump to content
SAU Community

Recommended Posts

Car question:


Whats an equivalent spark plug for BCPR7ES or something that is a decent copper plug that can suit up to 400rwkw (including 400kw).

And can I buy them off a shelf.
If so, where. All info seems to have disappeared about 2012 re: Spark plugs and none of this stuff is on shelves anymore and I want to buy them on the weekend, in Melbourne.

 

Car question:

Whats an equivalent spark plug for BCPR7ES or something that is a decent copper plug that can suit up to 400rwkw (including 400kw).

And can I buy them off a shelf.
If so, where. All info seems to have disappeared about 2012 re: Spark plugs and none of this stuff is on shelves anymore and I want to buy them on the weekend, in Melbourne.
 

Bkr7e but try R and E auto parts on centre rd springvale. Next door to repco. They usually have stock of bcpr7es. If you get stuck I have a set of 6 that I've only used for 50km. Replaced them chasing a misfire that turned out to be something else.
  • Like 1

I have some iridium 8's that were $75 a plug and were scheduled to last a lifetime. They haven't given me an issue but I do get misfires at 20psi (380+kw).

So I thought to stop using amazing super plugs, and wanted a basic plug that is known to work, as its cheaper to try that first than replace Splitfires (which are now getting on in age, almost 10 years).

I got a misfire at idle that went away, and I'd like to have plugs in my hand ready to go should they be needed instead of looking ages later when I have a car running on 2cyl or some shit.

Car question:

Whats an equivalent spark plug for BCPR7ES or something that is a decent copper plug that can suit up to 400rwkw (including 400kw).

And can I buy them off a shelf.
If so, where. All info seems to have disappeared about 2012 re: Spark plugs and none of this stuff is on shelves anymore and I want to buy them on the weekend, in Melbourne.
 


I was using bcpr7es plugs at 394rwkw.
So I would just get those.

Guess I'm headed to RE Autoparts then!

They seem harder to find than most, these plugs, figured people would have found some other alternative on a shelf. Good to know the BKR7E is usable if in a pinch

2 hours ago, Kinkstaah said:

Whats an equivalent spark plug for BCPR7ES or something that is a decent copper plug that can suit up to 400rwkw (including 400kw).


And can I buy them off a shelf.

I get my BKR8's from Springvale Autobarn. or Bursons. i cant rememeber. I got a box of em.

24 minutes ago, admS15 said:

Everyone stocks 6 heat range but not many have 7. Greg also give bursons a call if r and e has no stock. So are you planning a track day this weekend ?

Nope, just had misfires at 20psi and a random one at idle today so wanted to have something on standby.
$80 plugs you use "forever" I don't trust to actually last forever :P

Nothing lasts forever, especially plugs. I got sucked into iridium's once, never again on a modified car. Copper for life. Like birds, I buy them in bulk. Last couple of times through spares box, where about $4 each and free delivery on overs over $50.

How the f**k did you research plugs on SAU and then buy iridiums expecting them to last?

There has to be at least a hundred threads telling you not to bother and just use BCPR7ES

Iridiums aren't a total scam per se, they do last for many times longer than normal plugs do...but the assumption made by the marketing claim is that they aren't going into a high performance car. A daily driver can use iridiums and will probably not notice a degradation after 50,000km etc. because performance decreases aren't as obvious nor are the plugs performing in an extreme environment. Iridiums wear like copper plugs do, but will retain say 70-80% of their performance after 10,000km, unlike the latter. This is useless in a high performance environment where you want plugs to be delivering 95%+ and as Iridiums can't do that any better than copper, better off saving your money.

On ‎7‎/‎7‎/‎2017 at 11:03 PM, joeyjoejoejuniorshabadoo said:

How the f**k did you research plugs on SAU and then buy iridiums expecting them to last?

There has to be at least a hundred threads telling you not to bother and just use BCPR7ES

I didn't research here. I spoke to Trent @ Chequered while my car was literally being tuned, and asked him what plugs to recommend for my setup at the time, taking in account my timing, ease of change, desire to not have it blow out and for it to last forever.

What he recommended did just that, I never had spark issues until I took a lot of timing away, and took a lot of boost away.

So I was asking on a more common setup, which is closer to what I have now, and the BCPR7ES work really quite fine, no misfires at all and I'm really happy with that, and really not that hard to change or check. The old plugs really were going strong but not suited to what I am doing now (they were also too cold a range, looking at them out of the car)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...