Jump to content
SAU Community

Recommended Posts

3 hours ago, admS15 said:

I've put 98 in a few times just to purge/clean the fuel system and felt like punching myself in the nuts every time. Engine is so much smoother and lively on ethanol. i'd rather pay the premium but United are still price gouging kents.

I can't back it up scientifically, but I feel like switching fuels periodically has to do some good. That being said, a couple times switching back to 98 I've wound up with cracked factory fuel hoses. It's interesting that it happens when switching to 98 as it's technically the ethanol that should be damaging them.

My idle is definitely smoother on ethanol and the midrange is vastly superior...and when accelerating under boost. Cold, off boost or for immediate / low down torque, my 98 tune feels smoother and faster in some ways, however I think this could be fixed in the ethanol tune. Both tunes are years old and neither were touched up since original. Also think I have a leaking injector. Also think I have a bearing that slaps quietly only on startup. Old cars gon be old.

I can't back it up scientifically, but I feel like switching fuels periodically has to do some good. That being said, a couple times switching back to 98 I've wound up with cracked factory fuel hoses. It's interesting that it happens when switching to 98 as it's technically the ethanol that should be damaging them.
My idle is definitely smoother on ethanol and the midrange is vastly superior...and when accelerating under boost. Cold, off boost or for immediate / low down torque, my 98 tune feels smoother and faster in some ways, however I think this could be fixed in the ethanol tune. Both tunes are years old and neither were touched up since original. Also think I have a leaking injector. Also think I have a bearing that slaps quietly only on startup. Old cars gon be old.

I had the exact same experience with the factory fuel hose after running 98. Small cracks in the outer skin of the rubber. I work for a rubber company, so I had the best grade of rubber we have extruded into fuel line size. See how that holds up. Each time I have run 98 I replaced the fuel filter afterward. I have 3 filters at home I've been meaning to cut open. I'll try get around to it this weekend.
  • Like 1
Mount it low and improve the balance!
Saw a learner getting someone to help him get his 250 off the ground the other day. They really should teach learners how to do that by themselves at the course...


I thought you had to be able to get a 125 or 250 up solo to pass the course? Or is it different down there?
went to winton last year, left with full tank and five jerry cans @ 22l each. Total of 175lt. i didn't participate in the last session coz i cooked the brakes and still had to stop just before i got home and top up to make sure i made it. I easily burn over 100l at sandown which is just down the road. On track, usage is close to 1km/l   #E85life #emptywallet #needunitedshares


I got 77L per 100km at Wakefield on 98 So it's about what you would expect usage to be for e85.
36 minutes ago, TiTAN said:

 


I got 77L per 100km at Wakefield on 98 So it's about what you would expect usage to be for e85.

 

Guess you don't have this problem anymore. 

Guess you don't have this problem anymore. 


Not with the flog. Disappointingly small tank though, takes 45L to fill when the fuel light comes on (~60km "range" remaining) and gets me a bit over 400km. ~60L tank would have been more appropriate imo.
13 hours ago, TiTAN said:

 


I thought you had to be able to get a 125 or 250 up solo to pass the course? Or is it different down there?

 

Different down here, never had to do that 7 years ago 

 

16.1l / 100km in the ol v8, average speed of 33km/h explains it

32 minutes ago, UNR33L said:

Different down here, never had to do that 7 years ago 

 

16.1l / 100km in the ol v8, average speed of 33km/h explains it

Could be worse like 30-35l/100km from the Clubby I had lol 

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
×
×
  • Create New...