Jump to content
SAU Community

Recommended Posts

6 hours ago, UNR33L said:

I HATE how that is expected & considered the norm. 

Contract states 37.5 or 40 hours yet to actually get anywhere you got to do 50 

(Because ofcourse time at work directly correlates to how good at the job you are right?)

My contract is 38 hours a week but I work 10 hours a day x5 days a week wah

1 hour ago, L33SH said:

My contract is 38 hours a week but I work 10 hours a day x5 days a week wah

Having just seen your pay agreement for next year I'm not pulling out the violin <3

Having just seen your pay agreement for next year I'm not pulling out the violin

 

 

Yeah, I do feel a bit better about being at work by 7.20am every day [emoji106]

 

And also losing my voice [emoji106]

I rock up at what ever time I feel like, normally around 11am.

Unless shits seriously broken which has happened a couple of times as something critical has crashed or failed spectacularly in such a way that everything else stops. Then at the very least I am working from home or I have to go into the office/site.

Hamish, need halp.
Went to reserve a table at Ezard for this Friday night, but can't get a table before 9pm. Need recommendations for somewhere similar. Any ideas?
 
 


Matteo's

lol, office plebs

I was going to go out to grab some lunch today, but realised I was still wearing my PJ pants and couldn't be stuffed walking two rooms over to put on my jeans. Life is hard.

lol, office plebs

I was going to go out to grab some lunch today, but realised I was still wearing my PJ pants and couldn't be stuffed walking two rooms over to put on my jeans. Life is hard.


Meh... I can work from home whenever but I chose to go to the office most days.

Worked at home with my last job, we didn't even have an office to go to.

Was nice waking up late and working in ya jocks m8, mostly watching youtube videos with downtime 

It gets old after a while, feel like a hermit crab that never leaves the house

Edited by UNR33L
  • Like 1
1 minute ago, Leroy Peterson said:

What games coming out worth upgrading for?
Toby on the quake hype train.

None really, I upgraded for BF1 but the game was sheit so never play it. Essentially got a $3k gaming PC and only play CS:GO / DOTA2 (which could be ran on a much cheaper system) 

Forza 7 will be good and can be run on Windows 10, be nice on a wheel. 

Gotta have dat PC swag doe. 

Edited by UNR33L

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...