Jump to content
SAU Community

Recommended Posts

Got myself a set of ID1000, mechanic tried to drill my OEM rail, ended up leaking.. so I'm back to square one. I already have a Nismo Type-A regulator so I would prefer to keep the single entry/nismo FPR and just get the cheapest 11mm fuel rail. Which one would it be ? or it doesn't even exist ( they are all dual entry) ?

I'm not looking for fancy fuel setup with AN hose or mega 2000cc or E85 setup, so i reckon a simple fuel rail design would work as long as it's not a china knock-off with poor sealing thread than these are pointless.

Is this what you are after? it mates the stock reg with an aftermarket rail.

Or just find a replacement stock rail and get the correct injector adapters... and a new mechanic. :P

post-63525-0-46605600-1440554618_thumb.jpg

  • Like 1

Is this what you are after? it mates the stock reg with an aftermarket rail.

Or just find a replacement stock rail and get the correct injector adapters... and a new mechanic. :P

Agreed.

This would not have been a problem

Is this what you are after? it mates the stock reg with an aftermarket rail.

Or just find a replacement stock rail and get the correct injector adapters... and a new mechanic. :P

never seen an adaptor like that, so i suppose this is what i need lol or maybe i would be better off with an external FPR.. how much this adaptor cost ?

edit: found this.. radiumauto. seems like they are the only one making an adaptor for aftermarket rail to bolt-on stock/Nismo FPR https://www.radiumauto.com/FPR-Adapter-for-Nissan-P602.aspx

Edited by cobrAA

If you won't be adjusting fuel pressure then you'd be fine with the OEM FPR.

Also the stock rail and injector adapters is probably the best solution if that is the case. The HKS rail and adjustable FPR is just going to be bling you won't even need.

Are you looking to adjust fuel pressure?

I won't, but I know the tuner had to adjust pressure with my gt2860's old setup.

If it's needed, I will get the big package, but i want to avoid bling factor. I'm aiming good HP, but I don't really plan on trashing the car so I thought the Nismo would be fine, but then I had second thought and i need to decide on my fuel setup ASAP since car should be done within a week

I don't understand why your injectors don't fit the stock rail, there should be no need to drill the rail out to match the injectors, in fact you would be mad to as it would never seal.

Can you take a picture of what you bought? I am sure I can point you in the right direction...

  • Like 1

I won't, but I know the tuner had to adjust pressure with my gt2860's old setup.

Shouldn't have to adjust pressure unless injectors were not up to the task and he was trying to push more fuel through.

Shouldn't have to adjust pressure unless injectors were not up to the task and he was trying to push more fuel through.

They were 700cc sard. maybe they were, in fact, not up to task.

I don't understand why your injectors don't fit the stock rail, there should be no need to drill the rail out to match the injectors, in fact you would be mad to as it would never seal.

Can you take a picture of what you bought? I am sure I can point you in the right direction...

It was a BNR32 rail. Mechanic said it didn't fit. over-bored as he said it was leaking after the mod. So now, we're back to square one.

Either I buy my friend's BNR34 rail and bring it to a machine shop ( I say ppl who couldn't make the ID1000 11mm fit and had to drill and some say that with lots of lube/pressure it fitted..)

or I buy HKS rail + adaptor + FPR + hose

The gtr rail won't accept 11mm, you need smaller adapters than that. The many hundreds I have sold have all fitted fine. What makes you think an aftermarket rail will help?

Did you tell ID they were for a GTR? If so send them back.

you have the wrong adapters.... in 2mins you can fix it by getting the same adapters as ive listed below... these are a bit dear @7ea though so shop around.

http://www.asnuperformance.com.au/gallery/Injector%2BExtensions/injector-extension-adapter-to-10mm-denso/123094?view=grid

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drive beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
×
×
  • Create New...