Jump to content
SAU Community

Recommended Posts

I've got a 98' Series 2 Stagea and the 4wd doesn't work (See more here: http://www.sau.com.au/forums/topic/463038-help-with-fault-finding-attesa-system-attesa-ecu-c34/#entry7685341)

Just wondering how do i retrieve error codes relating to the 4wd system? I've got to the ABS/ESP computer (Also 4wd?) and a few forum posts reference a red flashing light through a hole or someone said it is on the PCB itself. I've pulled the cover off the computer and could not see a light anywhere (See photos attached).

Is there another way to get the codes?

post-142543-0-27873800-1455871490_thumb.jpg

post-142543-0-58007600-1455871491_thumb.jpg

post-142543-0-03844800-1455871494_thumb.jpg

Asked a mate today who said he might have one. If I shorted out the two pins and got 5 slow, 5 fast (No fault?), Will the consult pickup on the 4wd light error?

I'm from Gosford,NSW (1 hour north of Sydney)

My understanding of that list is that it's saying the 4wd light wouldn't be illuminated for error 55 on that list?

Also that list corresponds to the led flashing light on the Attesa ecu in the boot (which mine does not have a flashing led)?
Is there another list hidden away somewhere that corresponds to the consult port fault codes?

No luck so far mate. Got a mate with a consult connector so I'm going to chuck it on tomorrow and see if it comes back with anything.

If you work it out please let me know mate

looked into this beforehand pal unless yours is an s2 ? won't work i don't think the main problem for me is the fact i can't fine my diagnostics plug almost like it has been cut of

Just checking - it should be behind the coin tray but sometimes they seem to fall down or otherwise become detached. Have you had a look upwards from under the dash (need to be a bit of a contortionist)?

Just checking - it should be behind the coin tray but sometimes they seem to fall down or otherwise become detached. Have you had a look upwards from under the dash (need to be a bit of a contortionist)?

i have looked right under the dash i can see the grey plastic bracket from its plug where it looked to have snapped off of its mount i may remover the lower dash section soon

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hang on. Let me get this straight. The desire is to have coilovers, BC in particular, to be MORE comfortable on Sydney roads than stock suspension? Well, that's obviously not right. BCs have crude damping design at the very best, and typically hard spring rates. BC stands for Billy Cart. And then, the desire is to put in some shitty old worn out stockers, to get it blue slipped and then put the BCs back in? And then.....what? Not worry about getting pulled up by the Plod? Because you seem to have raised a worry about paying for engineering (which actually does solve all your legality problems) and still getting pulled up.... but the only problem there is that if/when that happens you have to show your paperwork at the inspection station. Whereas, if you just swap in borrowed shitty old stockers to get it slipped now, and then you get defected in the future, you have to go find more shitty old stockers then too. You course of action looks like this set of options: Buy brand new stock type dampers, and springs. probably cost a bit more than $1k all up, but will last for the remaining life of the car. Put them in, pass inspection, drive on them forever more. Hell, they could even be really nice Bilsteins and Kings or other lower&stiffer springs if you wanted. Get the car engineered as is. ~$1k. Buy new Shockworks coilvers (or MCA) and also pay for engineering. You're spending a lot more here. But these will be the best things that you could drive around on.
    • Might be worthwhile hitting up Facebook's groups, I know most of them contain terrible people and scammers - however you might be able to find someone that's in Sydney with factory suspension you could purchase and/or hire. Just do not send any form of money anywhere, in person cash only.
    • Thanks @Duncan Ride height is fine. I think it's almost stock tbh. Happy to share a pic. I don't actually have a regular mechanic as haven't lived in Sydney too long. Could you or anyone recommend any shops in Sydney?
    • You just need a different blue slip shop (preferably one you regularly use as a mechanic), and make sure the coil overs are as close as possible to standard height
    • yeah the sugar refining companies were pushing for the same in Oz originally, all fuels were going to have 10% ethanol to make them "cheaper" (noting, that the loss in l/100 might be greater than the decrease in price). I guess they won that fight in Canadia
×
×
  • Create New...