Jump to content
SAU Community

Recommended Posts

I've got a 98' Series 2 Stagea and the 4wd doesn't work (See more here: http://www.sau.com.au/forums/topic/463038-help-with-fault-finding-attesa-system-attesa-ecu-c34/#entry7685341)

Just wondering how do i retrieve error codes relating to the 4wd system? I've got to the ABS/ESP computer (Also 4wd?) and a few forum posts reference a red flashing light through a hole or someone said it is on the PCB itself. I've pulled the cover off the computer and could not see a light anywhere (See photos attached).

Is there another way to get the codes?

post-142543-0-27873800-1455871490_thumb.jpg

post-142543-0-58007600-1455871491_thumb.jpg

post-142543-0-03844800-1455871494_thumb.jpg

Asked a mate today who said he might have one. If I shorted out the two pins and got 5 slow, 5 fast (No fault?), Will the consult pickup on the 4wd light error?

I'm from Gosford,NSW (1 hour north of Sydney)

My understanding of that list is that it's saying the 4wd light wouldn't be illuminated for error 55 on that list?

Also that list corresponds to the led flashing light on the Attesa ecu in the boot (which mine does not have a flashing led)?
Is there another list hidden away somewhere that corresponds to the consult port fault codes?

No luck so far mate. Got a mate with a consult connector so I'm going to chuck it on tomorrow and see if it comes back with anything.

If you work it out please let me know mate

looked into this beforehand pal unless yours is an s2 ? won't work i don't think the main problem for me is the fact i can't fine my diagnostics plug almost like it has been cut of

Just checking - it should be behind the coin tray but sometimes they seem to fall down or otherwise become detached. Have you had a look upwards from under the dash (need to be a bit of a contortionist)?

Just checking - it should be behind the coin tray but sometimes they seem to fall down or otherwise become detached. Have you had a look upwards from under the dash (need to be a bit of a contortionist)?

i have looked right under the dash i can see the grey plastic bracket from its plug where it looked to have snapped off of its mount i may remover the lower dash section soon

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
    • It's TWO steering wheels actually. 😛 one for each hand They are wheels, and they steer!
×
×
  • Create New...