Jump to content
SAU Community

Recommended Posts

I have had over 25 cars in my life BUT the windscreen reflection on my 34 is something else, never had anything like this before. Had to change the undies a couple of times when I got home, lol

Always drive with sunnies on during the day.

I drive a lot early in the morning on a bendy road, come out of, or into a corner into the sun and the road disappears, I mean , gone! white out!

Cleaned inside and out, run the washers when it starts to look dirty ish, use the sun visor and still scary. :yes:

I put a black mat out of the Tiida on the dash and that helps a lot, 50% better but that goes where it wants when you accelerate hard . Just ordered a R34GTR dash mat and and I am sure it will help the glare.

Just wonder if some type of tinting could help or maybe it has been used and is the problem because it has scratched up or something ????

Funny you brought this up. I had the exact same thing happen today, first time ever I was driving blind.

The windscreen just needs a proper clean. Sometimes you need to re do it over and over again until streaks and glare are gone.

What do you use to clean your inside? Most products leave a film behind that will intensify glare.

Hi Peter,

Use - 0000 fine steel wool you can get from Bunnings on the outside of your windscreen.

Give it a good rub over.

Then use Rainx following instructions.

Lastly get a 10-15cm sun strip for your front windscreen.

  • Like 2

Funny you brought this up. I had the exact same thing happen today, first time ever I was driving blind.

The windscreen just needs a proper clean. Sometimes you need to re do it over and over again until streaks and glare are gone.

What do you use to clean your inside? Most products leave a film behind that will intensify glare.

I have to say , driving blind(not drunk) is one scary Mother f er

Some of the protectant products for the dash are too shinny, I think the angle of the windscreen and how close it is to the dash might also play a part ?

I have some glass polish and I will try it in the morning and see how that works ?

I have the Bosch GEX 150 Pro sander/polisher and all of the different microfibre cloths, pads, polish and a glass cleaning kit. Think I will have to get serious with it :)

Just did the drivers side earlier this morning and went for a run and it is a bit better but the mat I covered the dash with works the best to help stop the reflection.

I will have the full R34GTR dash mat coming early this week and I will do a full windscreen clean and polish and see how it goes.

The windscreen is only 1 hand width away from the dash at the front of the dash, on the Tiida, it is 1 hands width close to the windscreen and I have no reflection problem, I just wonder if the dash being so close to the windscreen could cause the reflection ?

This is why I HATE silicon on the interior.

Way too much glare.

Also, watch the glass polishing, as it can cause warped vision if you create high/low spots.

Sun in your face is easy, just drop the sun visor but that reflective glare is something else. It is only very early or late driving, no problem at other times. Maybe my eyes are stuffed ?

But , I have never had this type of glare in any other car and have used Armor All?

In the 34GTR it makes everything disappear, bloody scary, better than a radar camera to make you drive UNDER the speed limit :)

Now I have to watch out if I polish it unevenly , cant win, lol

I use Repco Eclips , not as shinny as Armor All but still shinny

Going to get super fine 0000 steel wool later and also try the Rainx

But I think the Dash Cover will do the trick and it has the cut outs for the Aircon etc. I will take a couple of pics and post them, should have it tomorrow.

Thanks

cleaning the windscreen wont help much, its only good if its hazy and affects your vision at night, but doesn't appears to be the case

its probably just a fundamental design issue with the car - shape of the dash and the angles between dash, windscreen and driver's head

Plastidip the dash matt black :P.

Funny you said that , got the dash mat today and stuff me if it is not a Nylon or similar and Fn sparkles when the sun is on it. I will go for a run in the morning and see what happens.

Plastidip, have to look it up ??????

If it is crap I was thinking a matt black spray might be ok, not too sure how it would look or smell , should be OK when totally dry ?

cleaning the windscreen wont help much, its only good if its hazy and affects your vision at night, but doesn't appears to be the case

its probably just a fundamental design issue with the car - shape of the dash and the angles between dash, windscreen and driver's head

I think the design is the issue, windscreen very close to the dash and maybe since I am short I am closer than most ?

Funny you said that , got the dash mat today and stuff me if it is not a Nylon or similar and Fn sparkles when the sun is on it. I will go for a run in the morning and see what happens.

Plastidip, have to look it up ??????

If it is crap I was thinking a matt black spray might be ok, not too sure how it would look or smell , should be OK when totally dry ?

plasti-dip is a mat black spray.

AFAIK, its a liquified rubber.

You can pull it off fairly easily too.

plasti-dip is a mat black spray.

AFAIK, its a liquified rubber.

You can pull it off fairly easily too.

Probably do the job, but sounds like it might look a bit rough sitting on top of the dash ?

The dash mat is not a flat surface, some sort of carpet like material. Might try some black dye first if the mat causes glare, could always try the plasti-dip after if needed and if it comes off easily there should not be a problem if it looks a bit off :/

Let you know how the glare is tomorrow and take a pic, the mat itself looks , well OK ish but better than I thought it would look :)

Or you could use a pillow......jus sayin'

Hahaha, first car was a 1936 Dodge @ 15, needed 2 pillows,1 to lift me up to see over the bonnet and the other so I could work the clutch, brake and go go, so do not knock the worth of a good pillow or 2, lol

Had a run this morning but left a bit late but there was no glare with this dash mat, have to do it again earlier or later this arvo to get a true result

As you can see from the pics, there are cut out for the aircon and passenger airbags. So at least they put some thought in making it.

post-52098-0-28305500-1464651626_thumb.jpg

post-52098-0-87032900-1464651693_thumb.jpg

Oh gawds one of those mats. I'd spray the mat a, erm, matt colour to remove the shiny-ness.

That is the plan if it does not cut the glare down and with that Nylon type matting I guess it will not be too good. I think I will try the dye first to see how it goes ?

Have you had one of these, hard to tell when you see them on the web :/

Fit OK

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...