Jump to content
SAU Community

Shockworks Presents Round 9 - Sandown Raceway 1st Oct | Grand Final Day


Recommended Posts

Hey guys I have fixed the track day requirements link for anyone not sure what is required for a car and driver to attend.

 

http://www.sau.com.au/forums/topic/453779-track-day-requirements/

  • Like 1

Cams Manual Schedule D - Apparel

http://docs.cams.com.au/Manual/GeneralRequirements/GQ05-Schedule-D-2016-1.pdf

We're "Race" / "Multi Club"... So Helmet level is "B"...

In the table it seems to list "E22 (with 03, 04 or 05 amendments)" which looks like your helmet. But don't quote me on that, that table is confusing as hell.

  • Like 1

Ha ha yeah thanks for that@Odium i found that table super confusing too ! Just strange you dont need a as/nzs sticker on a road approved helmet

3 hours ago, OYEAHA said:

Ha ha yeah thanks for that@Odium i found that table super confusing too ! Just strange you dont need a as/nzs sticker on a road approved helmet

 

Sorry was busy earlier could not reply in length.

 

the ECE is accepted by vic roads as well now so it's not just CAMS that are accepting it.

 

so Snell, ECE, AS and BS we accept.

 

 

  • Like 1

Thanks Martin :)

Yep in my search for the answer I came across an article saying that they were road legal in Victoria since mid 2015, but still illegal if you travel to certain other states on your motorbike (ridiculous considering that you can be considered "Safe" in a $75 helmet, but not in a $750 helmet)

Thanks for the clarification

Hello :-)
I just bought a fire extinguisher, its a 1kg cams approved, the date on the neck is 03 2016. The lovely man at the shop assured me that it was the make date i just want to confirm. Is it valid 3yrs from that date? Im having trouble getting my head around whats an expiry date/make date. Any help would be appreciated. Tegan

that is correct 3 years from the date stamped on the bottle.

 

so good till march 2019

 

make sure it is bolted in, no cable ties/tech screws and such.

 

M

19 minutes ago, fdrx7 said:

Hello :-)
I just bought a fire extinguisher, its a 1kg cams approved, the date on the neck is 03 2016. The lovely man at the shop assured me that it was the make date i just want to confirm. Is it valid 3yrs from that date? Im having trouble getting my head around whats an expiry date/make date. Any help would be appreciated. Tegan

Yes that is correct. 3 years from manufacture date

Unless it specifically says "Expiry Date" then consider it a Manufacture date, as different uses have different time spans (for the same equipment)... Stupid I know.

  • Like 2
On 9/26/2016 at 10:35 PM, acsplit said:

I was just about to post this, yep contact brendan during office hours garage $50 can fit two cars

Damn that's cheap, PI was like 4 times that




  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...