Jump to content
SAU Community

Shockworks Presents Round 9 - Sandown Raceway 1st Oct | Grand Final Day


Recommended Posts

Hey guys I have fixed the track day requirements link for anyone not sure what is required for a car and driver to attend.

 

http://www.sau.com.au/forums/topic/453779-track-day-requirements/

  • Like 1

Cams Manual Schedule D - Apparel

http://docs.cams.com.au/Manual/GeneralRequirements/GQ05-Schedule-D-2016-1.pdf

We're "Race" / "Multi Club"... So Helmet level is "B"...

In the table it seems to list "E22 (with 03, 04 or 05 amendments)" which looks like your helmet. But don't quote me on that, that table is confusing as hell.

  • Like 1

Ha ha yeah thanks for that@Odium i found that table super confusing too ! Just strange you dont need a as/nzs sticker on a road approved helmet

3 hours ago, OYEAHA said:

Ha ha yeah thanks for that@Odium i found that table super confusing too ! Just strange you dont need a as/nzs sticker on a road approved helmet

 

Sorry was busy earlier could not reply in length.

 

the ECE is accepted by vic roads as well now so it's not just CAMS that are accepting it.

 

so Snell, ECE, AS and BS we accept.

 

 

  • Like 1

Thanks Martin :)

Yep in my search for the answer I came across an article saying that they were road legal in Victoria since mid 2015, but still illegal if you travel to certain other states on your motorbike (ridiculous considering that you can be considered "Safe" in a $75 helmet, but not in a $750 helmet)

Thanks for the clarification

Hello :-)
I just bought a fire extinguisher, its a 1kg cams approved, the date on the neck is 03 2016. The lovely man at the shop assured me that it was the make date i just want to confirm. Is it valid 3yrs from that date? Im having trouble getting my head around whats an expiry date/make date. Any help would be appreciated. Tegan

that is correct 3 years from the date stamped on the bottle.

 

so good till march 2019

 

make sure it is bolted in, no cable ties/tech screws and such.

 

M

19 minutes ago, fdrx7 said:

Hello :-)
I just bought a fire extinguisher, its a 1kg cams approved, the date on the neck is 03 2016. The lovely man at the shop assured me that it was the make date i just want to confirm. Is it valid 3yrs from that date? Im having trouble getting my head around whats an expiry date/make date. Any help would be appreciated. Tegan

Yes that is correct. 3 years from manufacture date

Unless it specifically says "Expiry Date" then consider it a Manufacture date, as different uses have different time spans (for the same equipment)... Stupid I know.

  • Like 2
On 9/26/2016 at 10:35 PM, acsplit said:

I was just about to post this, yep contact brendan during office hours garage $50 can fit two cars

Damn that's cheap, PI was like 4 times that




  • Latest Posts

    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...