Jump to content
SAU Community

Recommended Posts

I

On 9/21/2016 at 1:36 PM, r32-25t said:

Higher lift help a lot with power and maybe a little response but longer duration is a massive detriment to response, it's actually surprising how little duration it takes to have a big effect  

Its also suprising how little duration you need to make big power..

there is so many overcammed rbs going around..people like to point out peak figures..it means shit..its all about the power under the curve and how wide it is with a h pattern!

cheers

darren

  • Like 2
On 9/22/2016 at 1:45 PM, khezz said:


So what would be your recommendation for cams. For the type of setup discussed in this thread. 2.6l, e85, 750-800hp turbo. Going for 500kw at all fours?

mine made 500kw on JEM's dyno with just a set of HKS drop in 256 cams 8.7mm lift

the problem with going bigger lift is the costs start to go up cause you need to mess around with the head even more

i was actually very surprised the cams didnt 'hold back' power as I was originally told go with 272 cams

JEM told me - lift makes power - duration moves the power up and down the rev range...

  • Like 1

Agree totally ^^

People are too quick to throw big lift/duration cams in these days to the point of even making up custom high lift/low duration and bashing the valve train unnecessarily when there is more important things to sort out.

Ive made 5540wkw on a portedhead with 256 9.5mm kelfords (basically poncams)  Smart money gets spent where the greatest gains per dollar are first [emoji16]


What's does your fuel system consist of, if it's not a secret?

What's does your fuel system consist of, if it's not a secret?

Fire hose style lines and had to eliminate the injectors all together as they were providing a restriction just straight fuel line in the intake manifold does the trick for this bad boy
On 9/18/2016 at 8:37 PM, khezz said:

I should point out that this is not regarding any particular car. Just want to see experienced people's views. It seems that high mount twins are dead as dead can be. Low mounts are old tech.

My car will be getting a pair of low mount Gtx units. In search of 450awkw. The cost of engineering papers puts a high mount single out of reach.

so do you want feelings or factual numbers? because depending on a few factors their result will probably vary from yours.

I suppose numbers would be more useful. Different drivers will describe feelings differently. I have now been forced to go the single turbo rout. Going for the precision. So numbers would be great.

Holy, phone typo induces mass hysteria!

We were all very impressed and kinda worshipped you for a while. Thanks for ruining it.

So what sort of fuel system are you running. Fuel pump and injector size? Please
  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...