Jump to content
SAU Community

Recommended Posts

HiLol...was a rev up since he doesnt want to share any info. I am guessing he will install bleed nipples before he tries to chirp 3rds :)

 

Looks like Cayenne calipers on a 324-332mm rotor of sorts as it all still fits under a 17" wheel.?!?!?!?!

Probably work quite well on the smaller rotor. Problem with Cayenne calipers is they come with varying piston sizes depending what model Cayenne they are off.  You need to have the ones with the smallest pistons to have a real chance of it being a good bolt on setup otherwise without ABS it will just be locksville

There are adapters available now to run the brembo 17z or 18z calipers with z34 355mm rotors for Z / S / R (non gtr only) chassis cars. Also kits for gtr's (& Z/S chassis) to run AMG 8 pots with the 355mm discs

 

Great work designing your own to work with gtr's though

Edited by lidz
21 hours ago, GD51LA said:

that's allot of man hours that i don't want to give away

i could sell you a kit front and rear for approximately 4k

How does this benefit anyone if you're not willing to share any information? What's the point in even posting about it then?

wheel stud hole need to be drilled to nissan stud pattern

these are the smaller cayenne calipers designed for 330mm rotors off the v6 cayenne (330mm cayenne rotors)

the pad meets perfectly with the rotor surface

anything else?

Yes. Where did u get 4 grand from as an asking price and what advantages do you see in these over the evo brembo kits, and what master cylinder have you found a skyline to require during your testing of this prototype kit.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
×
×
  • Create New...