Jump to content
SAU Community

Recommended Posts

49 minutes ago, hy_rpm said:


Offt! shitbox
Almost a $50k build i wouldnt sell it not worth it

Is there a sneaky 3.2L stroker here you aren't telling us about?! ?

2 hours ago, Dose Pipe Sutututu said:

Decided to update my spreadsheet, turns out "cheap shit box project" isn't so "cheap" after all.

 

image.png.fad6f261960df98643a49e6f825b0bed.png

At least you arent in denial about what you have spent lol

20 minutes ago, admS15 said:

Im clearly doing it wrong... Still below 20k brah.

Not including consumables like brake pads and tyres.

Mine doesn't include tyres, pads, maintenance shit either :(

 

Keys were handed to a mate whilst it was in New Delhi. Safe to say the clutch, gearbox and engine seem to be working well.

 

  • Like 4
12 hours ago, V28VX37 said:

8/10

Would have been 9 but needs more gauges

More like needs a working tacho Hahah.. At present rev limiter is at 8300rpm soft cut and 8500rpm hard cut.

#becausehonda 

  • Like 1

Gifts run pre Lunar New Year (yes I'm Asian and no I won't go back to my country becasue I'm already here ?).

Still no time to throw it on the dyno yet but AFRs are in the low 11s and timing isn't anywhere even barely close to a stock map (actually used my old map and flatten the timing due to cams).

20180215_105354_Burst01.thumb.jpg.598d2b223ec53e5500a27610a90f44dd.jpg

  • Like 2
5 hours ago, Dose Pipe Sutututu said:

Gifts run pre Lunar New Year (yes I'm Asian and no I won't go back to my country becasue I'm already here ?).

Still no time to throw it on the dyno yet but AFRs are in the low 11s and timing isn't anywhere even barely close to a stock map (actually used my old map and flatten the timing due to cams).

20180215_105354_Burst01.thumb.jpg.598d2b223ec53e5500a27610a90f44dd.jpg

All i can say is LOL. 

5 hours ago, Dose Pipe Sutututu said:

Gifts run pre Lunar New Year (yes I'm Asian and no I won't go back to my country becasue I'm already here ?).

Still no time to throw it on the dyno yet but AFRs are in the low 11s and timing isn't anywhere even barely close to a stock map (actually used my old map and flatten the timing due to cams).

20180215_105354_Burst01.thumb.jpg.598d2b223ec53e5500a27610a90f44dd.jpg

All i can say is LOL. 

Without an idle correction rate vs. timing compensation table, getting the car to idle this smoothly wasn't easy! Had to pull a few Microtech tricks haha

 

  • Like 1
9 hours ago, Dose Pipe Sutututu said:

Without an idle correction rate vs. timing compensation table, getting the car to idle this smoothly wasn't easy! Had to pull a few Microtech tricks haha

 

y u no lumpy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Started sifting thru my brakes to decide which ones I will run on Clem   Made me think I should just put them all on Silver...for when brake fade just isn't an option   Should be able to bump rotor up from 343x32 to 348x36 off Supra. Not sure if the Supra annulus is right for the Alcons or APs but trying g to find a used Supra\M4 rotor to test fit The Alcons seem to gain 1-2mm clearance which all helps  
    • So car is getting a few mods to the cage and some jacking points welded in Meantime Ol Silver gets a new gearbox and shiny clutch.  Old Box is being set aside for Clem  
    • Probably speedometer itself if the odometer is ticking. If the needle is stuck from a bit of grease or something that can cause it to stay at 0. Or a cracked solder joint in the speedometer can do it too.
    • Thanks Fella’s   to take this off topic and to elaborate a bit more. I have an rb25/30 going into a r32 GTST.. expected to make around 600-700hp. Would you?   A) R34 GTT box   B) CD00#?  I’ve seen a few posts about the CD swap and sounds fairly involved with making it fit etc but if it’s worth the work then I’ll go that way
    • Lower at the hubs. Funny I forgot to mention that part. Do this pull here I turned the camera off too soon but the graph shows a drop at the top and that was because the pipe from the turbo blew off. The tuner said we could’ve made possibly another 15 whp. He also added if I switched to ethanol we could up the boost some more as well. I was comfortable capping it at the most of 20 pounds. Turns out the turbo pipe just needed a new worm clamp. Got home replaced that then did a third gear pull from 3k to 7200 rpm and the power was great to the top. I just got an ecu mounting bracket from IEE that I need to try and get everything to fit well. It’s a PITA to get the harness and ecu fit properly behind that kick plate 
×
×
  • Create New...