Jump to content
SAU Community

Recommended Posts

49 minutes ago, hy_rpm said:


Offt! shitbox
Almost a $50k build i wouldnt sell it not worth it

Is there a sneaky 3.2L stroker here you aren't telling us about?! ?

2 hours ago, Dose Pipe Sutututu said:

Decided to update my spreadsheet, turns out "cheap shit box project" isn't so "cheap" after all.

 

image.png.fad6f261960df98643a49e6f825b0bed.png

At least you arent in denial about what you have spent lol

20 minutes ago, admS15 said:

Im clearly doing it wrong... Still below 20k brah.

Not including consumables like brake pads and tyres.

Mine doesn't include tyres, pads, maintenance shit either :(

 

Keys were handed to a mate whilst it was in New Delhi. Safe to say the clutch, gearbox and engine seem to be working well.

 

  • Like 4
12 hours ago, V28VX37 said:

8/10

Would have been 9 but needs more gauges

More like needs a working tacho Hahah.. At present rev limiter is at 8300rpm soft cut and 8500rpm hard cut.

#becausehonda 

  • Like 1

Gifts run pre Lunar New Year (yes I'm Asian and no I won't go back to my country becasue I'm already here ?).

Still no time to throw it on the dyno yet but AFRs are in the low 11s and timing isn't anywhere even barely close to a stock map (actually used my old map and flatten the timing due to cams).

20180215_105354_Burst01.thumb.jpg.598d2b223ec53e5500a27610a90f44dd.jpg

  • Like 2
5 hours ago, Dose Pipe Sutututu said:

Gifts run pre Lunar New Year (yes I'm Asian and no I won't go back to my country becasue I'm already here ?).

Still no time to throw it on the dyno yet but AFRs are in the low 11s and timing isn't anywhere even barely close to a stock map (actually used my old map and flatten the timing due to cams).

20180215_105354_Burst01.thumb.jpg.598d2b223ec53e5500a27610a90f44dd.jpg

All i can say is LOL. 

5 hours ago, Dose Pipe Sutututu said:

Gifts run pre Lunar New Year (yes I'm Asian and no I won't go back to my country becasue I'm already here ?).

Still no time to throw it on the dyno yet but AFRs are in the low 11s and timing isn't anywhere even barely close to a stock map (actually used my old map and flatten the timing due to cams).

20180215_105354_Burst01.thumb.jpg.598d2b223ec53e5500a27610a90f44dd.jpg

All i can say is LOL. 

Without an idle correction rate vs. timing compensation table, getting the car to idle this smoothly wasn't easy! Had to pull a few Microtech tricks haha

 

  • Like 1
9 hours ago, Dose Pipe Sutututu said:

Without an idle correction rate vs. timing compensation table, getting the car to idle this smoothly wasn't easy! Had to pull a few Microtech tricks haha

 

y u no lumpy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
×
×
  • Create New...