Jump to content
SAU Community

Recommended Posts

Nek level steering wheel lock, saw this in Naples, Italy. Gosh what a shit hole lol... I suggest for anyone considering on visiting not to stay there, if you're going to the beautiful islands just go direct, don't waste your time in Naples (however the pizzas are so cheap it makes no sense, a double scoop of gelato cost more).

20190808_170650.thumb.jpg.8756d028e8d07a342e1fddbb2b9d1c3b.jpg

 

  • 2 weeks later...

I'm back in Australia, didn't get deported or stopped at boarder security!

Needed high heat for this dish and the induction stove top just won't cut it. Used a butane camping stove (with the holes drilled out), and I'm sure now the R33 is covered in oil splatter but at least it smells good.

20190818_191549.thumb.jpg.aed48e13da53f005ee3059365d4f9b29.jpg

  • Haha 1

Prev owner was into Auto Salon, hence the car is purple and he used a hammer to roll the guards (the car had wanky 19s on it) he didn't reseal the cracked paint and rust took over. Then when I needed to fit the 18x9.5 +22 with 255 wide semis, I went to town with a guard roller and destroyed both guards.

Also going to reshell next year so don't care :)

 

Hasn't moved in 2 months, just gets started, rev it a few times. Once it's warm, I commence a few anti-lag hits to spool the turbo and it gets turned off.

20190820_204506.thumb.jpg.5eb79770e455a6bae9a4f1939861fd8a.jpg

  • Like 1

Did one ages before but on shitty tyres, I fear trying in such a small space with semis might propel the car into the Tiguan lol

IMG-20150913-WA0009.thumb.jpeg.b440f935950fdeecc5551dfbb1d85899.jpeg

  • Like 2
  • Haha 3
2 hours ago, Dose Pipe Sutututu said:

Did one ages before but on shitty tyres, I fear trying in such a small space with semis might propel the car into the Tiguan lol

IMG-20150913-WA0009.thumb.jpeg.b440f935950fdeecc5551dfbb1d85899.jpeg

Rest it up against the tiguan. Then skid.

  • Haha 1

PowerFC delete, Nistune install, upgrade to Z32 street tuna. Ready for dyno in a few weeks, runs an Auto Salon special Garrett GT2871 from the 90s and Tomei Procams.

Owner wants it on 98RON only, should see 230kW to 240kW on crap all timing to preserve the motor.

 

 

IMG-20190825-WA0008.jpg

  • Like 3

Who's keen on buying the car as-is? I cbf, I can tune it before it goes too if the price is right.

OR is anyone keen on the car minus the motor, electronics (ecu, wiring, sensors) and fuel system? I'll leave the rest in (MCAs, KAAZ diff, all the suspension shit,  Bride seat, hectic ulleh stereo.

Clearly over it.

Straight up swap for a 335i F30 M-Sport with under 70k kms.

Getting that modern VW has changed me man, I didn't think it would affect me that much but it has.

The sheer lowdown torque, ridiculous gear shift speeds and luxuries has changed me for good.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...