Jump to content
SAU Community

Recommended Posts

Keeping this thread on topic. A bit of background, our house has the master bedroom on-top of the garage. So any heat/cold from the garage is pretty much transmitted into the bedroom floor.

Terrible in summer, terrible in winter. As the garage panel door is all aluminium, it's a acts as a massive heatsink. To slow down the effectiveness of this unwanted heatsink I decided to insulate the panels with 20mm Foilboard. Essentially it's just 20mm polystyrene with foil sheets either side. They are $44 a sheet (2.4x1.2m) from Bunnings, one side is reflective foil the other side some green snot colour. Ended up needing 4.5 sheets, could have done 4 if I joined left overs but yeah nah.

I didn't take any pre temperatures but once up I could instantly notice a difference inside the garage at about 11pm. This morning I walked in and also was quite pleasant to be inside. Looks like it worked and not to mention reflects a bit more light off the lights.

$240 (plus foil tape which I haven't applied yet, job for another day).

PXL_20220613_055629035.thumb.jpg.6e3a5350e0309e22018f23524a5c8f4c.jpg

 

Also took out the shit box on my Meat Emporium run. This time with the gate plumbed back and more boost 😎

PXL_20220612_231051196.thumb.jpg.1d34e75dbb8364566364319f52d7b731.jpg

PXL_20220612_231031365.thumb.jpg.0bbb6c9960a1876f480919a378a5c166.jpg

 

And my silly mate with a built Evo 3 has twisted my arm into going to All Jap Day on the 3rd of July. Will give this "roll racing" thing a go and the faux power cruise sessions a good go. If anyone is around, come say hi!

(Pray to all the gods I don't bin the motor, my track record hasn't been very good lately lololol)

Screenshot_20220613-232303.thumb.png.975449569eb001ce3423816eb564122b.png

 

  • Like 8

I did my old garage the same way, huge difference - well done. 

Good luck at event, actually act when a warning light comes on and you will be fine.

Rather than setup an oil pressure warning light and buzzer then ignore it when you know the car is suffering oil surge because Race Chrono says you're on track for a PB... Who would do that?!

 

  • Haha 2
On 14/06/2022 at 12:18 PM, ActionDan said:

Rather than setup an oil pressure warning light and buzzer then ignore it when you know the car is suffering oil surge because Race Chrono says you're on track for a PB... Who would do that?!

I actually logged in and disabled the engine protection (yeah I did that) LOLOL

Won't be doing that again!

Oh yeah, here's an idle video.

Barely can hear the lumps, running a cat, 1x muffler and 1x massive SMB muffler sure shuts up the car.

 

  • Like 7

Shit box updates, decided to go through the box of new OEM shit.

PXL_20220616_113140604.thumb.jpg.cffa30c1e41f58a02f71f8784e9bf27b.jpg

Quick wins, replace both cabin light lenses and upgrade from halogen bulbs to LED.

PXL_20220616_114653075.thumb.jpg.1b21c066e9b6261ec69cb88492625899.jpg

PXL_20220616_115803027.thumb.jpg.367873953dc8cef311479568b996d1a5.jpg

Before with the OEM halogen bulbs and yellowish lenses.

PXL_20220616_113722258.thumb.jpg.cc02f3ec31613add3aeb73888fc65861.jpg

 

And yeah my Bride Zeta IV seat will go back in for All Jap Day 😎

  • Like 2

Almost too nice now to track it now......

So good you are getting all those little things done as makes it nicer and modern, just need a heap of warning lights and you will have that bmw feeling.

 

  • Haha 4
On 17/06/2022 at 8:07 AM, robbo_rb180 said:

Almost too nice now to track it now......

I know right, I'm going to All Jap Day in Sydney on the 3rd of July.

They have a few Eastern Creek sprint sessions, which I believe are untimed but I'll give it a crack with Race Chrono running.

Why build a car and not enjoy it right? It's like having a hot missus that you can't have a poke from time to time lol.

  • Haha 4
On 17/06/2022 at 8:56 AM, Dose Pipe Sutututu said:

I know right, I'm going to All Jap Day in Sydney on the 3rd of July.

They have a few Eastern Creek sprint sessions, which I believe are untimed but I'll give it a crack with Race Chrono running.

Why build a car and not enjoy it right? It's like having a hot missus that you can't have a poke from time to time lol.

And along those lines, "turning off safety parameters is like shagging your Mrs sister, only to have your Mrs walk in the door, you may make a PD, or it may just explode" 

  • Haha 2
  • 2 weeks later...
On 28/06/2022 at 6:24 AM, Duncan said:

Still, it can probably chirp second

Hahah with cold tyres 2nd is pretty funny.

 

On 28/06/2022 at 7:41 AM, robbo_rb180 said:

how does it feel on the street?
How much torque did it end up making?

With that zf 8hp gearbox will be a weapon

On the street it's very linear, wasn't like any of my previous setups. The power is very very linear, a way to describe it is like a NA.

Here's a run on 0.5bar boost, power is ruler flat (minus the part where I turned off VCT a bit earlier)

PXL_20220627_042214190.thumb.jpg.b52b4bef7c017cb9a474ec7f41c024d1.jpg

Torque (derived) wise it made 611nm at 6400rpm

  • Like 3
On 28/6/2022 at 7:55 AM, Dose Pipe Sutututu said:

Hahah with cold tyres 2nd is pretty funny.

 

On the street it's very linear, wasn't like any of my previous setups. The power is very very linear, a way to describe it is like a NA.

Here's a run on 0.5bar boost, power is ruler flat (minus the part where I turned off VCT a bit earlier)

PXL_20220627_042214190.thumb.jpg.b52b4bef7c017cb9a474ec7f41c024d1.jpg

Torque (derived) wise it made 611nm at 6400rpm

House purchases, renovations, samsonas, dct swaps, garage door mods and I’ve forgotten what turbo this has on it. 

  • Like 1
  • Haha 2

@RBW49N lolololol...

It has a Garrett GTX3576R Gen 2 with a T3 1.01 divided rear housing. 

turbine side was pretty much on point, just undersized the compressor LOL.

  • Thanks 1

Here's the final power run, you see me looking at Alex quite a bit incase something didn't sound right so I could abort the run.

We did have misfires a few runs previously that sounded oddly like knock, ended up gapping down to 0.4mm on BCP7RES and that solved the issue.

 

  • Like 5
On 6/29/2022 at 10:14 AM, Dose Pipe Sutututu said:

And log of the final run :)

image.thumb.png.6b4cb0ded2ee54a2f6478eb5c31ab0c8.png

Will go decat OR 50 cell cat for next session lol

 

 

Is the car still on a flex setup or is it straight e85 now?

Looking at the base timing makes me feel anxious (thinking there is more timing in it from the e85 compensation table) but if that base timing is pretty much the total amount of timing then I can sleep at night again lol.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Scenic roads, stunning skylines, and Chickos to finish it off! Join SAU NSW as we cruise through the Royal National Park and along Lawrence Hargrave Drive to Figtree! Sunday 26th October 2025 4:30PM Meeting Waterfall Station Parking 5:00PM Cruise Departure Royal National Park > Lawrence Hargrave Dr > Memorial Dr > Sid Parrish Park 6:15PM Arrival at Sid Parrish Park Figtree Meet Location: Waterfall Station Parking Final Destination: Sid Parrish Park RSVP: https://forms.gle/E4s5SiRKQfDdypky8 *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • It's funny, as Ive seen plenty of people use them in cheap builds on YT. And they actually go okay, even though a lot of other maxspeedingrods stuff is terrible. Those turbos seem reliable enough, the only part being, a good quality turbo that is "identical" to it, will out perform it day in and day out. In both a lower boost threshold, and the ability to flow more air at the same boost pressure. As a cheap cheap replacement, not a terrible choice. For cheap and shouldn't blow in a day, not terrible (like other eBay/Temu turbos) for low cost and still decent performance, that's where the question comes in to play from the results I've seen. I'd actually find it hilarious to buy one, and strap it to a paddock basher or some other cheap as POS originally NA car, and send it to the moon!
    • The maxpeedingrods turbo is cheap and bolts on to stock parts. I think you just need a bigger silicone coupler for the intake. Its a cheap china turbo, but it's been running on mine for almost 3 years at 16-19 psi.
    • What do they look like right after you've tried to start it with everything connected? Also post photos of what they actually look like.
    • Also wanted to say, my new spark plugs are blackened looks like it's very rich. I have splitfire coilpacks but stock coilpack loom and ignitor. I tried directly grounding the ignitor ground to body as well. 
×
×
  • Create New...