Jump to content
SAU Community

Recommended Posts

Leaving your car in reverse gear while rolling down a hill

Hey guys,

Earlier today i turned into a steep hill street and I realised that it was the wrong street so I put it in reverse gear to pull out of the street but then a taxi came up behind me so I couldn't get out of the street. So I went down the hill but after going down about 50 metres I realised I still left it in reverse gear while my foot was pressed down on the clutch pedal. I only realised I left it in reverse gear when I heard that winding noise reverse gear makes so I immediately put it in neutral. 

I was wondering if this could damage the gearbox or any transmission system or anything else on the car. I tested reverse gear straight after and it still seemed fine but I just wanted to make sure.

thanks

Edited by IM-32-FK
I'm sure 50m won't cause a problem, but potential issue is that the oil pump is running backwards so no oil pressure in the motor for that time. 
 

Seen as his foot was on the clutch and im guessing the car must have been running (seen as it was being driven prior to this) for a start would not have been an issue.
  • Like 1

 

1 hour ago, Duncan said:

I'm sure 50m won't cause a problem, but potential issue is that the oil pump is running backwards so no oil pressure in the motor for that time. 

 

I'd like to here your reasoning for this Duncan....how does the oil pump run backwards?  This  - to my thinking - means that the motor was running backwards??

Only way I can think of this happening is if you are rolling backwards down a steep hill while its in say 3rd gear but the motor is switched off??? And if its switched off, no bang or boost so no oil pressure would not be a bad thing given the duration. But willing to learn.

1 hour ago, tridentt150v said:

Nope, not a thing.

Sorry forgot to mention that the front of the car was facing down the hill . I wasn't going down the hill backwards like I was reversing down the hill if u can get the picture

8 hours ago, Duncan said:

I'm sure 50m won't cause a problem, but potential issue is that the oil pump is running backwards so no oil pressure in the motor for that time. 

 

Haha, The engine runs clockwise no matter what gear you are in... Oil pressure would not be effected at all.

If you had of taking your foot off the clutch then best case scenario the engine stalls and you come to a abrupt stop... worst case something may have broken from the shock load..

But you didn't so nothing to worry about at all.

 

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
    • It's TWO steering wheels actually. 😛 one for each hand They are wheels, and they steer!
×
×
  • Create New...