Jump to content
SAU Community

Recommended Posts

Braking upgrade

hey all

did my first track day in my car ive just finished spraying. went really well and ran well all day with the exception of the braking.

First off they boiled there guts out by the end of each session. and the standard GTST stuff isnt up to scratch.

Obviously the easy way would be fit the GTR brembos. but they are pricey for what they are.

What are my other options? and what can i do to stop the boiling also?

Looking for all 4 corners 

thanks

19399721_10158955302765215_7190593453162086498_n.jpg

19400561_10155157369429550_3670939122459634837_o.jpg

Link to comment
https://www.sau.com.au/forums/topic/471023-braking-upgrade/
Share on other sites

1 minute ago, niZmO_Man said:

What pads, brake fluid in the car?

Look at ATTKD/D2/K-Sport/whatever kits.

That's what I'd use. Cheap, proven, good pad options.

In the meantime the GTST brakes aren't terrible so you might want to bleed it through with motul RBF600

Link to comment
https://www.sau.com.au/forums/topic/471023-braking-upgrade/#findComment-7837034
Share on other sites

6 minutes ago, Adz2332 said:

ok sweet thanks guys ill look them up.

K-sport, i havent heard anything good about them, all be it in coilovers. are they decent with brakes?

Would rather go with the attkd version from just jap. That way you get a proper warranty if something isn't right with the kit. I dont think i've read anything negative about these. Some guys had issues with the ksport with rotors having too much run out from new.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/471023-braking-upgrade/#findComment-7837040
Share on other sites

Actually I think they are smaller, certainly they allow a lower offset wheel to fit by a few mm. Caliper size itself is not an issue, its about pad size, where the pad is on the disc, piston size, caliper stiffness. Ksport and all the other brands seem to use the same design/tooling and probably the same factory. I've used multiple sets over the years and the only real difference I've seen are the size, PCD and number of disc to hat bolts which mean the rotors are not all interchangeable.

WIth that AP set, they look like a good option, just make sure you can get replacement discs before you buy. They will use the same pads as the ATTKD/Ksport/D2 etc

Link to comment
https://www.sau.com.au/forums/topic/471023-braking-upgrade/#findComment-7837047
Share on other sites

38 minutes ago, Dose Pipe Sutututu said:

You need adaptors, if you're after some decent braking power - go the Alpha Omega kit which uses the older Brembo from Evo 5-9 but uses the 350mm EvoX rotors.

 

its interesting that evo 7 8 9 all have the identical brembos. and can be had for a lot cheaper than gtr items

Link to comment
https://www.sau.com.au/forums/topic/471023-braking-upgrade/#findComment-7837066
Share on other sites

careful with brake sets that look cheap; make sure it includes bolt on adaptors for your hub and chosen disc, brake lines, discs/rings (+ hats if 2 piece) and usable pads.

the only experience I've had personally with willwoods was really disappointing; Neil has a set of 4 spot ones on the radical and you should see the caliper flex when you put your foot on the pedal. Also poor pad availability for that caliper. But I guess that can't be representative of every caliper they make or they wouldn't be in business.

the alpha omega seem like a worthwhile approach too, but again include the cost of calipers, lines, decent pads etc when comparing.

finally, keep in mind brake size vs wheels you have or intend to buy. wheels bigger than 18 get expensive for semi slick tyres.

Link to comment
https://www.sau.com.au/forums/topic/471023-braking-upgrade/#findComment-7837073
Share on other sites

You haven't said what fluid you are using, or how old it is. It's probably worth starting with a fluid flush, using a decent high-temp fluid (RBF600 as per Duncan's suggestion, or even better RBF660). The other worthwhile upgrade is ventilation - get as much air flowing through the brakes as you can.

The ATTKD brakes are good - we run the 8 pot / 355mm kit on a similar car & are very happy with it. We've got the stock rear brakes, and have no plans to change them - they are working fine with the 8 pot fronts. I wouldn't bother stuffing around with used Brembos. The airflow & fluid suggestions will still apply with a BBK.

How many laps are the sessions you're doing? 

Have you considered entering a Supersprint at Mallala - the next one is on July 16th. Supp Regs are at Supp Regs - there should be at least 2 R33s running.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/471023-braking-upgrade/#findComment-7837096
Share on other sites

30 minutes ago, GeeDog said:

You haven't said what fluid you are using, or how old it is. It's probably worth starting with a fluid flush, using a decent high-temp fluid (RBF600 as per Duncan's suggestion, or even better RBF660). The other worthwhile upgrade is ventilation - get as much air flowing through the brakes as you can.

The ATTKD brakes are good - we run the 8 pot / 355mm kit on a similar car & are very happy with it. We've got the stock rear brakes, and have no plans to change them - they are working fine with the 8 pot fronts. I wouldn't bother stuffing around with used Brembos. The airflow & fluid suggestions will still apply with a BBK.

How many laps are the sessions you're doing? 

Have you considered entering a Supersprint at Mallala - the next one is on July 16th. Supp Regs are at Supp Regs - there should be at least 2 R33s running.

what class do you run?

Link to comment
https://www.sau.com.au/forums/topic/471023-braking-upgrade/#findComment-7837102
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
    • Continental have consistently beaten the absolute shit out of every other performance tyre in Wet/Damp/Cold conditions and give up a little bit of time (half a second at most) in the dry. Almost like it's engineered for German conditions or something. I'd def give those a try.
×
×
  • Create New...