Jump to content
SAU Community

Recommended Posts

First pic its the oem boost solenoid. Do you have some sort of boost controller installed?

Second one looks to be somekind of diy switch. Could be for anything really. Possibly a power switch for aftermarket gauges, lights or something like that. Only way to find out is to follow the wires

Link to comment
https://www.sau.com.au/forums/topic/475399-what-is-this/#findComment-7891059
Share on other sites

First picture is a boost solenoid which may have been connected some type of boost controller before it was unplugged.

Second photo is a on/off for something as others have said - if you want to find out take it out and then follow the wiring. My guess is it was for something boost related but has since been removed. Very stealthy to have it mounted by the door.

Third photo is a fire extinguisher holder. Most Skylines (all, if I’m not mistaken) came with portal fire extinguishers but most have been removed.

Cheers.

  • Confused 1
Link to comment
https://www.sau.com.au/forums/topic/475399-what-is-this/#findComment-7891068
Share on other sites

11 minutes ago, adey88 said:
2 hours ago, FedBpy2018 said:
Is this thing normal? 
20181114_202509.thumb.jpg.0c90dde661037708166d582c79ae0439.jpg

I believe that's for a flare (not fire extinguisher) as required by law in Japan.

Actually, now come to think of it...I think you correct. Then some people place fire extinguishers there but originally yes it was a small black flare.

Link to comment
https://www.sau.com.au/forums/topic/475399-what-is-this/#findComment-7891074
Share on other sites

1 hour ago, Robocop2310 said:

Actually, now come to think of it...I think you correct. Then some people place fire extinguishers there but originally yes it was a small black flare.

People don’t put fire extinguishers there because it will be hard to reach while in the drivers seat, usually it’s on the right hand side of the passenger foot well or under the drivers/passengers seat. Also the flares are red.

 

  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/475399-what-is-this/#findComment-7891079
Share on other sites

5 minutes ago, Milkmun said:

People don’t put fire extinguishers there because it will be hard to reach while in the drivers seat, usually it’s on the right hand side of the passenger foot well or under the drivers/passengers seat. Also the flares are red.

 

Right, you are (photo of flare on same spot).

images?q=tbn:ANd9GcSvXAHjllvKPsvxpO5YHvo

 

Link to comment
https://www.sau.com.au/forums/topic/475399-what-is-this/#findComment-7891081
Share on other sites

Since you are not using the stock boost controller you must have an alternative. The simplest would be an R32 actuator. Trace back from your actuator to see where the line goes and you will find an aftermarket controller if fitted.

Link to comment
https://www.sau.com.au/forums/topic/475399-what-is-this/#findComment-7891090
Share on other sites

I followed the wires from the actuator they lead inside the dash through the firewall and cant follow from there, this sunday im going to take the dash apart and find it, has anyone got a guide to do it? If it was a car i normally work on i could take it apart in less then 5 mins lol, im guess for this it will take a few hours to pull apart and put back

Link to comment
https://www.sau.com.au/forums/topic/475399-what-is-this/#findComment-7891151
Share on other sites

14 minutes ago, FedBpy2018 said:

I followed the wires from the actuator they lead inside the dash through the firewall and cant follow from there, this sunday im going to take the dash apart and find it, has anyone got a guide to do it? If it was a car i normally work on i could take it apart in less then 5 mins lol, im guess for this it will take a few hours to pull apart and put back

That's a factory boost solenoid with factory wires that will lead back to the factory ecu. Hardly worth chasing, certainly don't pull your dash apart to solve this non mystery.

Link to comment
https://www.sau.com.au/forums/topic/475399-what-is-this/#findComment-7891153
Share on other sites

3 minutes ago, FedBpy2018 said:

So dont bother using it then?

Well, that depends on what other boost control you have.

 

Also, there is an obvious misunderstanding as to what terms is being used here.  The item in the photo is the boost control solenoid, as others have said.  The "actuator" referred to by Kiwi is not that solenoid.  He meant the actuator that is mounted on the turbo that pneumatically pushes on the wastegate lever.  Not the same thing at all....although, obviously, related.  All part of the boost control.  Anyway, there are no wires on the actuator.  There wires on the solenoid are as Ben said.  You should follow all advice given.

Link to comment
https://www.sau.com.au/forums/topic/475399-what-is-this/#findComment-7891157
Share on other sites

From what i can see inside the car there is no other boost controller, also what causes a door window to tilt towords the inside of the car? Photos attached, the purple line on the window is the window hitting something on its way up so i dont use it but previous owner did, the first photo is what a owner had done to bypass the solenoid

20181115_203504.jpg

20181115_203621.jpg

20181115_203703.jpg

Edited by FedBpy2018
Link to comment
https://www.sau.com.au/forums/topic/475399-what-is-this/#findComment-7891163
Share on other sites

Unless that's an RB20 actuator (and I can't be stuffed searching the part number to check).....then you have a whole 5 psi and your car should be as slow as all f**k.

The window is easy.  The stuff inside the door that keeps the window aligned (so, either the runner channels/rollers or the felt pads near the top) are stuffed.

Link to comment
https://www.sau.com.au/forums/topic/475399-what-is-this/#findComment-7891165
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...