Jump to content
SAU Community

Recommended Posts

Hi everyone, I'm seeking advice with a fuelling issue. My fuel tank had a leak and i took my car(1990 r32 gts-4) to a mechanic to get it fixed up. He fixed the leak and replaced my lines since they were old and cracking. When driving home, when coming to a stop my car would just drop to 0rpm and stall. I took the car back to him and he said i had a bad fuel pump and replaced it. I got my car back, but now my car was idling at 1400-1500rpm. I got home and saw that he had unplugged my TPS, and so it was just going on the fall back system and idling around 1500rpm. After plugging the TPS back in, the car had the same fuel pressure issue. I put a fuel pressure gauge in and when turning the ignition on, the pressure goes up to around 50psi. When i start the car it backs off a bit, down to around 35psi and then just slowly drops to zero and stalls. 

Does anyone know what this guy could have done or has anyone had this problem before? Just looking to know what I should be checking first. 

Link to comment
https://www.sau.com.au/forums/topic/475418-fuel-pressure-dropping/
Share on other sites

14 hours ago, Nomu said:

Hi everyone, I'm seeking advice with a fuelling issue. My fuel tank had a leak and i took my car(1990 r32 gts-4) to a mechanic to get it fixed up. He fixed the leak and replaced my lines since they were old and cracking. When driving home, when coming to a stop my car would just drop to 0rpm and stall. I took the car back to him and he said i had a bad fuel pump and replaced it. I got my car back, but now my car was idling at 1400-1500rpm. I got home and saw that he had unplugged my TPS, and so it was just going on the fall back system and idling around 1500rpm. After plugging the TPS back in, the car had the same fuel pressure issue. I put a fuel pressure gauge in and when turning the ignition on, the pressure goes up to around 50psi. When i start the car it backs off a bit, down to around 35psi and then just slowly drops to zero and stalls. 

Does anyone know what this guy could have done or has anyone had this problem before? Just looking to know what I should be checking first. 

So the car has proper fuel pressure when the tps is unplugged?

The fuel pump control module has likely failed. When the car drops back to idle it is supposed to drop the speed of the fuel pump to prevent excessivly circulating fuel. Sounds like the low side is playing up

Direct wire your fuel pump through a relay as suggested

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...