Jump to content
SAU Community

Practical to buy an auto 34 GTT and convert to manual?

Uni<Skyline
 Share

Recommended Posts

Uni<Skyline Rookie

Uni<Skyline

Posted
Posted

As the title says iv been in the market for a manual r34 gtt coupe for a few months now. Watching how the market is going im seriously starting to consider buying an auto r34 gtt and then just paying for the conversion (and mechanic labout cost)

The price range between a manual and an auto is insane. Iv been tracking a fairly clean r34 GTT 2 door for a little bit around 14k, however if i wanted to buy a manual version of the car i would be looking at something around 19-20k 

Is that big of a price range practical or should i just buy a full conversion kit for around 1800 and pay a mecahnic to swap it for me?

GTSBoy Grand Master

GTSBoy

Posted
Posted

The usual answer is "don't take it on unless you are able to do it yourself". Perhaps that's less so for gearbox conversions than turbo engine swaps, but it's been the usual advice.

However, where there are availability issues and the price difference is that wide, sure it's practical. I did it to my R32 many many many years ago.  It's not difficult, just need all the things and enough skills to make the wiring changes, etc.

Jordy32 Experienced

Jordy32

Posted
Posted

If you can do it yourself sure, but you want to be sure of what you're getting in that particularly "Conversion Kit" because $1800 won't get you very far if you're buying all parts brand new.

So yes, but just be careful and mindful that extra costs can pop up, especially if you want to do everything 100%

Kinkstaah Grand Master

Kinkstaah

Posted
Posted

The conversion cost is about ~1k-1500 for a mechanic to do if for you, so think closer to 3500-4K installed and running.

After that your only issue is the auto steering wheel, but you can always use the buttons to trigger something if you want to get fancy. It is worth doing if you find a really nice auto 34 that is unmolested or has the (other) modifications you are looking at.

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

There are quite a few conversion threads so go through them and make a list of all the things you will need - many conversion kits do not come with e.g. gear lever (c/w knob and boot) centre console, complete clutch including flywheel, clutch pedal and hydraulics, handbrake, speedo drive,  the list goes on so make sure you write everything down (it will be a long list) and compare it with what you get with the kit. Here they are asking 2,500 to 3,500 for a kit and then you don't always get all that you need. Most importantly make sure its a proper RB25 "big box".

I converted my C34 Stagea because manual ones were/are so rare but if I were you I would keep looking for a manual Skyline.

hardsteppa Grand Master

hardsteppa

Posted
Posted

If you can find a decent auto, i say go for it. Mine was auto and i only coverted to manual 'cos it was time' but i see nothing wrong with going that way - as you say, can be a huge price difference when buying the car in the first place. My conversion kit was 1750aud and i wouldnt have spent anymore than that. By the time you buy a decent new clutch kit, 1piece clutch line, new cylinders etc, better off just getting tailshaft, box and pedals unless you get a cheap full conversion kit.

  • 2 years later...
walperstyle Apprentice

walperstyle

Posted
Posted
On 5/8/2019 at 11:33 PM, KiwiRS4T said:

There are quite a few conversion threads so go through them and make a list of all the things you will need - many conversion kits do not come with e.g. gear lever (c/w knob and boot) centre console, complete clutch including flywheel, clutch pedal and hydraulics, handbrake, speedo drive,  the list goes on so make sure you write everything down (it will be a long list) and compare it with what you get with the kit. Here they are asking 2,500 to 3,500 for a kit and then you don't always get all that you need. Most importantly make sure its a proper RB25 "big box".

I converted my C34 Stagea because manual ones were/are so rare but if I were you I would keep looking for a manual Skyline.

Do you have links to said parts?  The problem with old forums is there are a bunch a broken links, missing pictures etc. 

mosquitocoils Veteran

mosquitocoils

Posted
Posted
On 7/10/2021 at 1:17 AM, walperstyle said:

Do you have links to said parts?  The problem with old forums is there are a bunch a broken links, missing pictures etc. 

I recently did a manual swap on my Stagea - here is the guide I used for that and a lot of it is the same for the skyline. Of course any mention of 4WD doesn't relate to you.

 

I also made a video of the process 

 

  • 4 weeks later...
walperstyle Apprentice

walperstyle

Posted
Posted (edited)
On 7/10/2021 at 7:59 AM, mosquitocoils said:

I recently did a manual swap on my Stagea - here is the guide I used for that and a lot of it is the same for the skyline. Of course any mention of 4WD doesn't relate to you.

 

Question:   I have a R33 GTS-T RB25 automatic in my R34 GT-T.  I also have on the bench... a pull type AWD staega transmission with bad gears, AND a Z32 TT transmission in great shape.    Is it going to even be possible to swap bellhousings from the AWD pull type transmission over to the Z32 and achieve a manual swap?  A spec clutch just came up for grabs, still in package, but I don't know if I can even use it.

Edited by walperstyle

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      Why am I hitting a power wall with my stroked RB25?

      By Dose Pipe Sutututu · Posted

      Just a thought, how come you didn't use a 4D table? So you essentially run 2x fuel and 2x ignition tables, and the table/map switch is handled when there's enough WMI pressure detected. This is mine, but using the flex sensor as the 4th dimension, note the slider at the bottom. Between 0 to 70%, the timing is blended/interpolated , once it goes past 70% ethanol full send
    • 677_GTR
      First time Skyline owner

      By 677_GTR · Posted

      Hi guys, after dreaming of owning a JDM legend for 20 years, I got the chance to buy a 1995 R33 GTR.  I live in a small country called the Solomon Islands which is in the pacific. There is no performance car scene here, however 90% of vehicles here are 2nd hand Japanese imports so there is a handful of JDM sports cars here, tucked away.  3 Evo VI’s, 1 180sx turbo, 2 GTO’s, 1 R32 GTR and 2 R33 GTR’s.    Only 1 Evo and a 33 (mine) are active. I’m hoping to set up a club to get these cars back in the road.    I’d known of my GTR for 9 years and always dreamed of owning it. At the start of this year I found it sitting outside a workshop waiting for a respray. It was in pretty bad shape, although running and driving perfectly apart from a big exhaust leak and worn out bushings. My brother in law who is a huge GTR guy came over for a holiday and I took him to see it, he got into my ear and I bought the car 2 weeks later as is.   I’ve had a pretty bad problem with alcohol and weed since 2020 and I really wanted to quit. So I used this as my motivation. I quit everything cold turkey and have been investing all my spare time into restoring this car. It’s honestly been the best experience and has been such a positive impact on my life.  There is no market for these cars here, no parts and no mechanics that can work on them, so if you wanted to sell one it would be pretty impossible unless you found the right buyer. After a bit of negotiating with the previous owner (a good friend) I got the car for $15,000 AUD ($85,000 SBD) which is insane.  I’ve almost finished doing a refresh on the engine, new turbos, spark plugs and split fire coil packs. Also new gaskets and seals, This car had no leaks to begin with, but it’s due now being 30 years old. . Next I’ll be working on the suspension, all new bushings, ball joints, king pins and new coil overs.  Then it will be body work, it has really bad rust in the boot floor, I have purchased a rear beaver cut from my bro which will replace the rusted out one. The car is originally KL0, but was burnt orange when it landed here, then it was resprayed toxic green and then Bayside Blue. I’m probably going to get it redone in Bayside Blue.  I’m super grateful to be able to enjoy this car and couldn’t have done it without my bro Chris from OG-JDM. Looking forward to the future with this car and hoping to get it on the runway at the airport here 😂  cheers fellas 
    • MBS206
      Nismo GT Pro LSD configurations

      By MBS206 · Posted

      Also, it is just about triangularity. The less angle, the easier it physically is to do. Think of the amount of slip you're getting, as how hard you need to push an object. More slip, equals pushing way harder. Then the ramp is how steep the hill is. The Accel is less slip, which means it takes less pushing (less slip) to get it to be able to push apart. However, the steeper sides on the decell means it will take a lot more pushing (slip) to get it up the ramp.
    • MBS206
      Nismo GT Pro LSD configurations

      By MBS206 · Posted

      It's the angle of the ramp from the vertical. You're measuring from the horizontal. To convert, take 90* minus your angle reference = Nismo Angle.
    • Kinkstaah
      Nismo GT Pro LSD configurations

      By Kinkstaah · Posted

      I agree, thus 45 degree is the *max* force one could apply to it. This is similar to what I've seen in uh... simulations... which allow you to play with diff ramp angles. Anything higher (or lower) than 45 degree would produce less force as 45 is the max... triangley.  I would state the 1 way is 90 degree, at least this is how my brain and other ways of explaining it refer to it. 90 degree also effectively acted completely open. I realise Nismo refer to it not as 90 (or 89) but "1". So I'm not understanding the angle on which these angles are based.
×
×
  • Create New...