Jump to content
SAU Community

Recommended Posts

Hi guys,

This questions might be stupid but when driving with a rb26 (r33 gtr), how much do I need to care about revs, fast throttle let off and stuff like this. 

My car has around 380 crank hp and 310 whp. (Bigger injectors, twin plate clutch, stock boost)

Of course regular maintenance is done :)

BR

Link to comment
https://www.sau.com.au/forums/topic/479185-how-careful-driving-a-rb26/
Share on other sites

As long as it is warm but not overheating, oil pressure is right and the tune is good, you should do everything to it, all the time, except hit the rev limiter more than briefly.

If you are doing track work on good tyres, oil surge causing loss of oil pressure can be an issue.

If your tune is not right for your fuel octane, or you have a fuel system problem (failing pump, pump wiring, clogged injectors, failing regulator) it could ping and melt a piston (keep an ear out for that, it is a distinctive "rock in a tin can noise")

If your timing belt, and the idler and tensioner bearings have not been replaced every 100,000, do so ASAP.

If it is misfiring, stop pushing it and sort out the problem (many causes)

If it uses oil between changes (I'd suggest every 5-10,000klm depending on what you use and how you treat it), start saving for a rebuild (head and/or bottom end)

  • Like 1
36 minutes ago, Duncan said:

As long as it is warm but not overheating, oil pressure is right and the tune is good, you should do everything to it, all the time, except hit the rev limiter more than briefly.

If you are doing track work on good tyres, oil surge causing loss of oil pressure can be an issue.

If your tune is not right for your fuel octane, or you have a fuel system problem (failing pump, pump wiring, clogged injectors, failing regulator) it could ping and melt a piston (keep an ear out for that, it is a distinctive "rock in a tin can noise")

If your timing belt, and the idler and tensioner bearings have not been replaced every 100,000, do so ASAP.

If it is misfiring, stop pushing it and sort out the problem (many causes)

If it uses oil between changes (I'd suggest every 5-10,000klm depending on what you use and how you treat it), start saving for a rebuild (head and/or bottom end)

Thanks so much for that info.

Helps me a lot. Btw i have the power fc installed, how high should i set the rev limiter? Any suggestions?

6 hours ago, fatz said:

If you are America (or wear a Gucci man purse in Australia) and like to sit in car parks in neutral banging the limiter for flames...they don’t like that

 

Haha no im not that type xd livin in europe (austria) my only goal is to keep that car healthy ✔

  • Like 1
5 hours ago, joshuaho96 said:

Don't bounce off the rev limiter, do a gentle warm-up of the engine, wait ~5-10 seconds for idle to stabilize after cold start and don't exceed ~50% throttle or 3000 RPM until coolant is over 70C. 

Thanks

4 hours ago, djr81 said:

8000rpm.

Seems a bit high or not?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Dear folks My family members have 4 different cars : Triton 2015 and Corolla 2011 and Mazda3 2012 and Hyundai Elantra 2014 Looking to buy engine oil funnel spill free What I found are are below  https://www.amazon.com/gp/aw/d/B0BBTTJNKX?ref=ppx_pt2_mob_b_prod_image&th=1 https://www.ebay.com.au/itm/145553221359?srsltid=AfmBOoqYBU6Ptw0LU_bAp_k67U3qkF97HHvePkA7iHZw8vUmiwoIRaRr https://www.amazon.com/gp/product/B09X23TCS5?th=1 Is there a funnel with attachment that fits most cars ? Don't mind to spend for a decent quality  Thx  
    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
×
×
  • Create New...