Jump to content
SAU Community

Recommended Posts

Ok, so now that I have some decent tyres to use at Wakefield I need to work on keeping myself secure. I was flopping around all over the place. I love my seats but they do nothing to help me stay in place.

Back in the day you could get WRX seats pretty cheap but I don't remember them being very supportive and I'm a fairly large guy and in need of some support.

Is a fixed back seat good to use on the day? Could swap the seats. Last fixed seat I tried (a Bride in my GTR) was super tight.

Once I have a seat I can look at reducing my body roll and then I can start lapping Wakefield in under a minute. 

 

 

 

 

And a half.

 

Link to comment
https://www.sau.com.au/forums/topic/481527-budget-track-seats/
Share on other sites

Have a look at https://www.velo.com.au/seats-3 

You can pop into Motorsport Connections and have a seat in them, see what you think. 

A harness makes a massive difference too, not sure if you'd be keen to go down that path, I'd say bolt in half cage, harness and fixed back seat is the way to go. 

Recaro's seem to be a bit bigger than Brides - and you can get knock off Brides in XL sizes through Just Jap etc

I put a Recaro SR3 in my R34, it's a tight fit for the seat in the car - and it's a good fit for me at 6'1 and 130kg (fat bastard!)

3 hours ago, Chris32 said:

you can get knock off Brides in XL sizes through Just Jap etc

We have one of these in our R33 track car. Had it for around 3 - 4 years, and works fine. Car is driven by 2 not-skinny-or-light drivers. 

You would also need a mounting bracket of some description. Ours uses a 1 piece bracket that bolts into the original 4 seat mounting holes, but the design of the bracket (and the fact that it's designed to get the seat quite low) means that it isn't a 10 minute job to install or remove - your 330i may be different.

5 hours ago, GeeDog said:

We have one of these in our R33 track car. Had it for around 3 - 4 years, and works fine. Car is driven by 2 not-skinny-or-light drivers. 

You would also need a mounting bracket of some description. Ours uses a 1 piece bracket that bolts into the original 4 seat mounting holes, but the design of the bracket (and the fact that it's designed to get the seat quite low) means that it isn't a 10 minute job to install or remove - your 330i may be different.

Hey mate, what bracket are you using? Thanks. 

On 11/19/2020 at 11:04 PM, Milkmun said:

Hey mate, what bracket are you using?

Not sure who makes it - we bought a pair (driver & passenger) off Gumtree about 5 years ago. They are specifically made for an R33 (and maybe 32/34?), and bolt into the original seat mounting holes. They look very similar to Ebay seat mounts

1 hour ago, PranK said:

The Just Jap Brides look pretty good. I love that the rails cost more than the seats! 

That's because the rails are Japanese Bride, and the seats are Chinese copies. The Bride rails pricing wrt proper Bride seats looks more reasonable - a real Bride seat is a ~$2000 proposition.

Whilst it is important that the rails/mounts be very high quality (even more so than the seats!), even the Jap Bride rails are not ADR approved. The "ADR approval" on the seats is pretty meaningless if the rails are non-compliant and/or not engineered.

45 minutes ago, GTSBoy said:

That's because the rails are Japanese Bride, and the seats are Chinese copies. The Bride rails pricing wrt proper Bride seats looks more reasonable - a real Bride seat is a ~$2000 proposition.

Whilst it is important that the rails/mounts be very high quality (even more so than the seats!), even the Jap Bride rails are not ADR approved. The "ADR approval" on the seats is pretty meaningless if the rails are non-compliant and/or not engineered.

Curious, have you seen/heard of any engineered seat rails?

Just now, niZmO_Man said:

Curious, have you seen/heard of any engineered seat rails?

No. If you wanted to get aftermarket seats with aftermarket mounts legal then you would need to get an engineer to do a report on the mounting system and sign off on it. What level of testing that requires is a bit unclear to me.

There are obviously any number of motor trimmers, etc, that fit Recaros to all sorts of vehicles, who probably know exactly which engineer to talk to. (Not suggesting that they know which engineer will do anything shonky to make it easier for them - just which engineers have the best approach to the task). Alternatively, they may have had to do some possibly destructive testing on the mounts that they use, and once they have approval based on that they might get some sort of type approval to keep using them in the same vehicle type with the same range of seats.

All I know is that if you go look at your state's vehicle standards website they will have something on there that says that seats must have OEM mountings or be approved.

23 minutes ago, GTSBoy said:

No. If you wanted to get aftermarket seats with aftermarket mounts legal then you would need to get an engineer to do a report on the mounting system and sign off on it. What level of testing that requires is a bit unclear to me.

There are obviously any number of motor trimmers, etc, that fit Recaros to all sorts of vehicles, who probably know exactly which engineer to talk to. (Not suggesting that they know which engineer will do anything shonky to make it easier for them - just which engineers have the best approach to the task). Alternatively, they may have had to do some possibly destructive testing on the mounts that they use, and once they have approval based on that they might get some sort of type approval to keep using them in the same vehicle type with the same range of seats.

All I know is that if you go look at your state's vehicle standards website they will have something on there that says that seats must have OEM mountings or be approved.

From my experience here in WA (possibly completely different to the Eastern States) - it is virtually completely impossible to get an aftermarket seat engineered, they just will not sign off on it. You can have the best quality seat with the best quality rails/mounts, it doesn't matter. Aftermarket seat is not going to get approved. 

 

On top of that, any seat that COULD be engineered (so meets the requirements of being able to slide forwards and pivot forwards) is not ideal for track work. For track work you ideally want a fixed back seat, and you need to make sure that it does not interfere with the operation of your seat-belt/harness at all. You shouldn't use a fixed back with a regular seat-belt because the sides of the seat interfere with the way the belt secures across your lap. If you are using a harness, you need to make sure that your shoulders are in-line with about the half-way point of the openings in the seat. If the openings are too low or too high, then it again interferes with the way the harness works and can either put the crash load on your spine or can spread the harness in a crash and make it possible for you to fly out.

 

Seats are not really something I would cheap out on, they are absolutely critical in a crash. While obviously the idea is not to crash - imagine giving yourself permanent spinal chord damage because you compromised on the seat. Obviously this gets hard for daily drivers with track duties, because you have different considerations for each application. You end up compromising for both situations and making both less safe. If I were to do it, I would have a dedicated race seat with dedicated race mounts that I swap in when I'm doing a track day, and keep the OEM seats for the street. 4-point harness with rear harness mounts on the floor and you can pull this out for daily duties and switch back to the seat-belt. Whole lot more effort, no where near as efficient as just having the one setup - but much safer in my opinion.

  • Like 1

Yeah, that's ^ pretty much the meat of the matter. The other states may or may not be different wrt how hard it is to get a seat install approved. I think it is possible here (in SA) but shudder to think what the additional cost would be, relative to the cost of the seats themselves.

I mean, while this is all true and all, I managed to get my V8 conversion fully engineered, and when doing so they must pass all elements of the car. It's like a super defect + RWC all in one.

It has aftermarket seats (OEM from a different car) and home made adapters (to adapt the seat to the rails)... which were/are Recaro rails for a R34.

This may not get the scrutiny you're worrying about, unless you've got bright blue/red seats or something that needs a HANS device or is a full fixed back style seat. I've used a harness with mine, and I wasn't going anywhere. All I can assume is that the engineers just figured they were stock seats.

But yeah. Don't cheap out on seats, harnesses, hans, safety. You may feel like a pillock with all the gear but if you're going home to a family at the end of the day no-one can really say you're being silly about it.

To be clear, the seats would only be for the track and I'd be swapping them out for the street. That said, I'm not interested in doing anything to compromise my safety. Initially I was looking at seats from other cars to use for the reason that they are OEM and strong. I wasn't aware that the rails are not ADR approved even if the knock-off seats were.

I did look at M3/M4 seats but holy smokes, they're worth as much as the car almost. 

Maybe once I fix the body roll I'll have less reason for seats.

I've used a GC lock on my MX5, that worked quite well, which whilst it is a major compromise compared to a proper fixed seat, harness and bar, it did hold my lower body in place.

I did need to pull it apart once and use some blue locktite as the allen screws came undone, once I had done that I never had an issue with it.

Opinions do vary on them though

download.jpeg.jpg.763670ea33b2a56ed8eb50e28961a877.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
×
×
  • Create New...