Jump to content
SAU Community

Recommended Posts

Hi sorry if someone has asked this before..I had a search :(

 

Just wanted to know if front brembo r34 gtr calipers direct fit onto gtt rotors with no issues..

My r34 came with front gold brembos and looking to change the worn down slotted rotors that it came with though im not sure if they are gtt rotors or a little larger or thicker?..thanx 

Link to comment
https://www.sau.com.au/forums/topic/481664-r34-gtr-brembos-on-gtt-rotors/
Share on other sites

Thanks I better do that..was seeing if anyone knew before i jacked it up..  was thinking it must be thicker then a gtt rotor...  though does a larger rotor fit?..  it would only be the thickness difference? Not a height or width difference?..   when I spin the wheel it sounds like the rotor makes a small grind sound when I try spin it..is this normal? Or shouldit free spin with no small grind sound?   ..sux when you get a car and not sure what someone has done or if it's riggt 

No. GT-T rotors are only 310mm diameter. GTR Brembo rotors are 324mm diameter. You cannot put a GTR Brembo on a 310mm rotor.

Just repetition for repetition's sake.

 

But.....GTR Brembo rotors aren't thicker. They're all 30mm. Only the 296mm GTR rotors are 32mm. Right?

1 minute ago, GTSBoy said:

But.....GTR Brembo rotors aren't thicker. They're all 30mm. Only the 296mm GTR rotors are 32mm. Right?

Correct for the R32 GT-R (non V-Spec, Sumitomo calipers) but some just throw on R33 GTS-t rotors as they're a bee's dick cheaper.

 

Haha Oh son of rajab . Its like that haha..I checked the pads and they are gtr bolt line up so few they are brembo gtr....I think i must be thicker as i measured and def past 310mm... came to past 320mm so must be 324mm..sorry to ask is the gtr r34 rotor different I size? Or is it just the thickness..should be right to get gtr r34 rotor it sounds? .thanx so much to all

Are you sure they are R34 GTR calipers? It is very common to install Z33 front Brembo calipers but the rears don't fit.

If you have front a rear Brembos then they would most likely be R34  GTR ones. And the rotors are different between 

BNR34 and Z33.

R32-R34 GTR 324mm rotors are all the same

The Z33 324mm rotors have a different hat height.

You'll need to measure this to work out what you have. Google how to measure rotor hat height and follow instructions.

 

 

 

 

  • Thanks 1

Ahh I'll look...they are the nice gold brembo that the had did z33 have gold?...crZy so z33 calpiers bolt dorr direct into the front if a r34? The bolt pattern to take them on and off...  thanks all I'll measure the height and all and see what size... they seem to take r34 gtr pads though looked up and z33 seems to have the same front pad.. so may be z33 brembos..

Thanx for the help guys..didn't want to buy the wrong one and have my wheels on And of alot..

1 hour ago, seriesII said:

z33 have gold?

Yes, here's a guide I wrote back then when I cared about sharing knowledge lol

http://www.trak-life.com/diy-350z-brembo-brakes-conversion-nissan-skyline-r33-gts-t-gts-gts-4/

  • Like 1
  • Thanks 1
On 18/12/2020 at 3:18 PM, Dose Pipe Sutututu said:

Yes, here's a guide I wrote back then when I cared about sharing knowledge lol

http://www.trak-life.com/diy-350z-brembo-brakes-conversion-nissan-skyline-r33-gts-t-gts-gts-4/

oh wow they do bolt into the same place and just a rotar change.. thank you for that.. seems it could be either brembo.. measure it is it seems. So I'll do that soon. Thanks to all who helped and cleared this up for me.. lol @ when I cared about sharing knowledge 🤣🤣 ..so gets like that 

My dust pan is still on my fronts and has the lip sitll..does this mean mine are r34 brembos and gtr rotors? As my dust pan is not hiting my rotor and has the lip..?..  in this guide for z33 calpiers you need to trim the dust pan lip or remove it for z33 rotors 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...