Jump to content
SAU Community

Recommended Posts

Have two quick spark related questions for everyone. I'm in the middle of building a stroked 2.8 and shooting for around 600kw. I'm expecting to run around 35psi to get there with my gen2 6466. 

1st - Will good condition splitfire coilpacks have any issues around that pressure/hp? Should I just purchase r35 coilpacks to be safe or am I wasting my money?

2nd - As for sparkplugs, I'm planning on running 8's with a .6mm gap. Will this suffice?

Thanks

Edited by TurboTapin
Link to comment
https://www.sau.com.au/forums/topic/483017-sparkplugscoilpacks-600kw/
Share on other sites

On 11/18/2021 at 11:19 AM, TurboTapin said:

Will good condition splitfire coilpacks have any issues around that pressure/hp?

They could be good, or they could struggle. I'd be worried that they're not good enough. It's not as if Splitfires are actually any better than brand new OEM coils. They're just the same technology level, well made.

On 11/18/2021 at 11:19 AM, TurboTapin said:

Should I just purchase r35 coilpacks to be safe

This would be my approach to anything above 400kW these days. Eliminate the possibility of trouble.

On 11/18/2021 at 11:19 AM, TurboTapin said:

2nd - As for sparkplugs, I'm planning on running 8's with a .6mm gap. Will this suffice?

8 is probably wise. I would want to be running fu(k tons more than 0.6mm gap. That's sufficient argument for R35 coils straight away.

R35 coils and the greatest spark plugs in the world, Denso IK01-24 or NGK R7434-8 and forget about it for a couple of years.

 

they can be had from RHD japan for relatively reasonable money. supercheap will hit you for $99 a plug.

Edited by burn4005
  • 2 weeks later...
  • 2 weeks later...
On 11/19/2021 at 2:18 PM, burn4005 said:

R35 coils and the greatest spark plugs in the world, Denso IK01-24 or NGK R7434-8 and forget about it for a couple of years.

 

they can be had from RHD japan for relatively reasonable money. supercheap will hit you for $99 a plug.

Could you explain the advantage of the Denso/NGK plugs you listed? Spark power, longevity, or something else my brain can't think of?

On 08/12/2021 at 7:09 AM, iruvyouskyrine said:

Could you explain the advantage of the Denso/NGK plugs you listed? Spark power, longevity, or something else my brain can't think of?

Yes - The NGK R racing plugs have iridium or platinum ground electrodes with a much higher melting point vs the iridium ix plugs having an iridium centre and nickel ground, so if you value your engine on a big dollar build you will run nothing else. A big detonation event or lean out and there goes your ground electrode through your cylinder.

Also they are available in colder heat ranges like 8 and 9 and have a concealed centre electrode which is helpful for large boost applications.

I personally have blown tips off the ix iridium plugs destroying my engine before and refuse to use anything else in a 400kw + engine now.

  • Like 2

DENSO IK01 24 IRIDIUM Denso racing track race dedicated special spark  plugs|plug f|plug playerplug and play solar power - AliExpress

the ground strap is pure platinum, and very short which keeps it cool to avoid pre-ignition events. electrode is iridium with a pointed tip. gap is fixed to 0.7mm.

very concentrated electric field, ground strap very good at dissipating heat and resisting ablation. 

 

  • Like 2
  • 2 weeks later...
  • 2 weeks later...
On 19/11/2021 at 2:18 PM, burn4005 said:

R35 coils and the greatest spark plugs in the world, Denso IK01-24 or NGK R7434-8 and forget about it for a couple of years.

 

they can be had from RHD japan for relatively reasonable money. supercheap will hit you for $99 a plug.

Shouldn't we be using NGK R7436 (JIS 53mm) instead of R7434 (ISO 50.5mm)?

On 11/01/2022 at 9:48 PM, R.3.2.G.T.R said:

Shouldn't we be using NGK R7436 (JIS 53mm) instead of R7434 (ISO 50.5mm)?

Yes that's exactly what I use on the 2.8. Having said that the plugs really jam into the R35 coilpacks hard - so much so that when you remove them the stalks usually come away from coilpack and get stuck on the plug which is totally annoying, requiring the entire one piece coil bracket to be removed to retrieve them. This is using the Godzilla motorsports bracket with R35 coils, so a PRP bracket might not have this problem if the spacing to plug is slightly higher.

The iso shorter length appears it would be a better fit I believe than the longer jic length but am yet to confirm this.

  • Like 1

 

On 18/01/2022 at 1:54 PM, GTSBoy said:

Some dielectric grease perhaps?

Could try it maybe, but it does appear that the R35 coilpack setup has always felt like the standard jic length, which is the correct ones for RBs, is the culprit. Comparing to stock or splitfires it's definitely more noticeably tight with R35 coilpacks with a BCPR type jic plug.

I'm pretty sure that's the reason @burn4005 is using the iso length instead of the jic as that 3mm shorter plug makes them fit the coil a bit nicer.

It's not that bad really, I'm just a bit pedantic and notice these types of things. The important thing is these plugs definitely are the best in the business.

Good point on R35 coils stalks @BK, I have R35 coilpacks on top of bcp7res (JIS) ATM, also not using PRP coil brackets

Don't have sticking issue but there is bit of gap when just resting coils springs on plugs

I think I'll just order set of JIS plugs as it's fitting ok with R35 coils as is

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...