Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...
On 3/22/2023 at 5:54 AM, PonieBoi said:

Rears can tuck 17x9 +30 with stock arms (bought camber arms all round just in case)

20 hours ago, GoHashiriya said:

Looks really nice, good work

Except that it is clearly too low at the rear (and presumably at the front) and will handle like a bucket of puss. The suspension arcs are not supposed to work with the wheel pushed that far up into the well.

If you're going to run it that low then you really should be using different bushes to push the rear subframe up towards the floorpan as far as it will go, and drop spindles. Drop spindles at both ends. The GKTech ones are good, and you will need/want to use their upper and lower arms with them also.

Edited by GTSBoy
On 05/04/2023 at 1:43 PM, GTSBoy said:

Except that it is clearly too low at the rear (and presumably at the front) and will handle like a bucket of puss. The suspension arcs are not supposed to work with the wheel pushed that far up into the well.

If you're going to run it that low then you really should be using different bushes to push the rear subframe up towards the floorpan as far as it will go, and drop spindles. Drop spindles at both ends. The GKTech ones are good, and you will need/want to use their upper and lower arms with them also.

Coilovers are how they came out of the box. Only just got the car home today.

Got camber arms for front and back but don't really need them.

Got the car home for the first time in nearly 6 months.

Fresh kit, paint job and wheels.

Next on the list is chucking in a non hicas subframe which I'm in the middle of doing the gktech reenforcement plates on, and also will be looking at new injectors and one of mine has a leak.

PXL_20230407_042956015.jpg

PXL_20230407_043025875.jpg

  • Like 2

Now that I can go back to working on this thing. Back to trouble shooting.

One of my problems is the car doesn't like to start again after it's hot (hot start). I have to disconnect the fuel pump to starve the motor, reconnect and start.

Got the injectors tested and cleaned, pretty much all above board. Will wack them back in, take the car around to Jaustech (SA), get the hot start config looked at.

 

PXL_20230412_072049789.jpg

Screenshot_20230413-115224.png

On 4/7/2023 at 3:38 PM, PonieBoi said:

Coilovers are how they came out of the box. Only just got the car home today.

Got camber arms for front and back but don't really need them.

What GTSBoy was mentioning has nothing to do with if they fit or not while stationary.

At super low ride heights, the top and bottom arms, along with the tie rods, move into some very odd areas, where as the wheel travels up and down, it will actually start to turn left and right.

Low ride heights, end up with bump steer.

 

Perfectly fine if you have a show car, but if you want to actually be able to drive down the road and have the car NOT automatically turn left and right unpredictably (with no steering wheel input) then super low height won't work. Camber isn't the only thing you need to worry about...

On 13/04/2023 at 7:09 PM, MBS206 said:

What GTSBoy was mentioning has nothing to do with if they fit or not while stationary.

At super low ride heights, the top and bottom arms, along with the tie rods, move into some very odd areas, where as the wheel travels up and down, it will actually start to turn left and right.

Low ride heights, end up with bump steer.

 

Perfectly fine if you have a show car, but if you want to actually be able to drive down the road and have the car NOT automatically turn left and right unpredictably (with no steering wheel input) then super low height won't work. Camber isn't the only thing you need to worry about...

I know what he meant haha. I've raised the car since then but the moment I got them out the box without adjusting them, that's how they sat.

 

 

 

 

  • Like 1
  • 1 month later...

Been a minute. Haven't really done much with the car. Just enjoying it.
Pretty much finished my non-hicas subframe.
Figured I'd re-enforce the tabs and mounts before it gets painted.
It's not pretty but for my first time welding, itll do alright haha.

dzvHClmW1EIEbTmayOdmR3dhNmQgbiJgETJkwb6a9lHkPhNIfT_Le6XklAvLcA1Dgah6yAXiyYp56vM6nhmd7wqnGCDX8UO-QXExDGh-T7YBuNUSudVh5x95_ZT9GQR1k1bqRMeyxp-XBhzKlI2gOw1iB7F6tkeZFCrUTniztHB7sF2-Zy31MjgJlL8floVZva_bD43qB4AAQZe3LopSrhFda6fwUW9rNF_CW7FYlvfZNFQ6B3iJfEJAx5zxpQq4kpY5rYJOMS8VvHDMmCEGVXaUFyqLkNpQ6nMM-xCnTULhIShIRJS5IFVkiiRqEkO_5f1ZXzftFGaNf223ATn6bRaIaJFey5LIhoJzZ5V5vnxzFhpZbFXt_p4mMQpdfD4N41tJDgiQqOl3hvKX_RUTemRqpSnl3zBxeMVrqeKAo7zGkkJa_EnVWMNbuAveq0_bl3n0GgldyPRyKRpwnSKPYlKQ5Zibr29njHfL6jTVnJbQivXm05G0EIBV1OJxRdS4lWUOzWMNpr-5p8iK1e_k52aQ6xGonPxpO8D_hiOvQG1Npv3Y-s9p2VVFl8a73LTKIEoTik5hgDpddS3KxDV2A8CoDVSYXWhTCGRD1hO30WmpFzc3-PQyI9igOIQZcxkLmIKkVPSvATLrBRusoc-YrJumY4l_DeeDIyeo8pszwTbt6nhRQEeg72yFJ8cZnzivTPWkT_lECkfzo-VvntwP0EK1ZyqPxwuS3PTlczbqizEVsXtspMarCb1Arg6J0JULaKmtvVhE0UhaHOeuzSJxphWrFHudYt1Cmnew9kNzypnFGhQ_xIxD1B7GL7l1w3KN46Ne6oqvA7Tj5t8ejlNluGWBfdueaE1rj9lcfTwk6CGaICc1YnHlNHZgiZKOVyG4ZcXH6xPhRSYU8cnX4Aqkryq5nBiP-8wVMGdIkTTNK-SmuxnOGQ=w1328-h1000-s-no?authuser=0

Pulled my knob too hard (haha) and shifter bushing became non existent. Went to get a gktech solid bushing from Sleekas and it turns out the bushing has worn that much, I need to get a new/not f**ked shifter. 

If anyone has other aftermarket options they have used, hmu.

PXL_20230603_034304178.jpg

PXL_20230601_071522531.jpg

Turns out there are 2 different sized shifter balls, and therefore 2 different size shifter bushes - noting they might both have the same outer diameter where they go into the gearbox

Looks like R32 sedan is the smaller shifter ball

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Also, I logged some data from the ECU for each session (mostly oil pressures and various temps, but also speed, revs etc, can't believe I forgot accelerator position). The Ecutek data loads nicely to datazap, I got good data from sessions 2, 3 and 4: https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-2?log=0&data=7 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-3?log=0&data=6 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-4?log=0&data=6 Each session is cut into 3 files but loaded together, you can change between them in the top left. As the test sessions are mostly about the car, not me, I basically start by checking the oil pressure (good, or at least consistent all day). These have an electrically controlled oil pump which targets 25psi(!) at low load and 50 at high. I'm running a much thicker oil than recommended by nissan (they said 0w20, I'm running 10w40) so its a little higher. The main thing is that it doesn't drop too far, eg in the long left hand fish hook, or under brakes so I know I'm not getting oil surge. Good start. Then Oil and Coolant temp, plus intercooler and intake temps, like this: Keeping in mind ambient was about 5o at session 2, I'd say the oil temp is good. The coolant temp as OK but a big worry for hot days (it was getting to 110 back in Feb when it was 35o) so I need to keep addressing that. The water to air intercooler is working totally backwards where we get 5o air in the intake, squish/warm it in the turbos (unknown temp) then run it through the intercoolers which are say 65o max in this case, then the result is 20o air into the engine......the day was too atypical to draw a conclusion on that I think, in the united states of freedom they do a lot of upsizing the intercooler and heat exchanger cores to get those temps down but they were OK this time. The other interesting (but not concerning) part for me was the turbo speed vs boost graph: I circled an example from the main straight. With the tune boost peaks at around 18psi but it deliberately drops to about 14psi at redline because the turbos are tiny - they choke at high revs and just create more heat than power if you run them hard all the way. But you can also see the turbo speed at the same time; it raises from about 180,000rpm to 210,000rpm which the boost falls....imagine the turbine speed if they held 18psi to redline. The wastegates are electrically controlled so there is a heap of logic about boost target, actual boost, delta etc etc but it all seems to work well
    • hahah when youtube subscribers are faster than my updates here. Yes some vid from the day is up, here:  Note that as with all track day videos it is boring watching after the bloopers at the start.  The off was a genuine surprise to me, I've literally done a thousand laps around the place and I've never had instability there; basically it rolled into oversteer, slipped, gripped and spat me out. On the way off I mowed down one of the instructor's cones and it sat there all day looking at me with accusing cone eyes as I drove past. 1:13:20 was my fastest lap, and it was in the second session, 3rd lap.  It (or me!) got slower throughout the day as it got hotter.      
    • It sounds like you want what the Toyota Landcruisers have for their roof racks. Wanna know what you end up with? Rust holes in the roof, and water everywhere...
    • Discovered today that if I select reverse first and take my foot off the brake, then select drive, the drive indicator light works and so does the tiptronic gear indicator. 
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Does anyone here have any ideas?   Cheers guys
×
×
  • Create New...