Jump to content
SAU Community

Recommended Posts

Hey all,

 

Is an ethanol content sensor required for an E85 only tune?

I was under the impression it was due to the variable nature of pump E85- which can vary wildy in ethanol content.

I guess my question is- can a tuner compensate for this with a flex fuel sensor or is it not required for straight E85?
 

I just bought one but i'm unsure if I should just return it.

Cheers all!

It's not strictly necessary, because, whilst the wildly "variable nature of pump E85" is a thing, it doesn't really vary so much that it has to be a problem. It can often be as low as 70, from what I understand, and even somewhat higher than 85. But here's the thing. The knock resistance from ethanol content pretty much reaches a maximum somewhere around 45% ethanol content. Thereafter the extra ethanol doesn't really provide much more ability to put in timing, safety from knock, etc. What it does do though is affect the required stoichiometry. For lower E content, you get richer (for a fuel system/table that assumes E85). So you get safer. And slower. Above 85%, unless the tune is pretty close to the edge of being too lean, you should still be fine. So if you want to keep your tune nicely optimised against varying E content, then....you need a sensor.

If it were me, I'd put a sensor in. The downside here is that you must do the full flex tune to get the benefit from it. You have to have a base map on one fuel and another on the opposite extreme of the E content to interpolate against. I wouldn't think that tuning on exactly E85 (or whatever happened to be coming out of the pump that day) would give the ECU anywhere to adjust to based on what the ethanol sensor is saying, unless there's that other fuel's tune in there also.

  • Like 1

I think it depends on whether you are using pump or can e85, the stuff direct from the refinery is pretty strict e85 I understand while the pump stuff varies from season to season to give you a chance starting the car on a cold morning.

I'd 100% put it in if I was even considering some ethanol.

  • Thanks 1

Personally even if I planned on running straight E85 all the time with no variability to account for cold start I would run a flex fuel sensor purely because any time you switch between pump gas and E85 you'd have to either fully drain the tank. I want to be able to switch to pump gas halfway, end up with E30 or whatever it ends up being and just keep driving without having to deal with AFR trims being all over the place.

If you were 100% sure that you will never ever run anything other then pump e85, then sure you could get away without running a flex sensor. 

Lets say the car was tuned on a tank of e80 and everything was setup perfectly on that %blend, as you drove the car and the ethanol content varied from e70 to e85 depending on what the fuel bowser was filled with at the time, you would not notice any change in how the car behaves. It would make the same power and drive exactly the same regardless of if it was currently at e70 or e85 or anything in-between. 

The only way you would notice anything is if you had a dash/gauge telling you that something was different, e.g. AFR is  currently 11.3 however when tuned it was 11.5 under the same circumstances. These small changes will be impossible to feel in the way the car actually performs.

So, should you use the flex sensor? I'd say yes, even if it was just to give you the option to use pump 98. There might be a situation in the future you haven't accounted for where you run out of e85 or it's not available for whatever reason, now at least you can still run the car happily on 98. 

Can you run without it, yes.

Should you, probably not.

My car runs 1 as it's flex tuned. I run e85 all the time, may run 98 once a year just to purge the system out.

In Victoria, the ethanol content from United pump e85 seems very consistent, my sensor reads it as 78-79%, have seen 80-81% a couple of times. I haven't verified how accurate my sensor is but wouldn't be too far off. This is over 5 years, never been under or over those figures.

On another note, you could get one of those portable ethanol test kits but you would need to take a sample each time. 

Since you already have the sensor, why not just use it. In future you may decide to run flex and it would be 1 less thing required.

  • Like 1
  • Thanks 1

Thank you all for the great replies.

The car plan is straight E85- as the engine isn't in great health with 130psi across all 6 cylinders on a factory 25DET- so low compression.

I want to prolong it while I save up for a rebuild. But I do hope for mid 400whp with E85 in the meantime.

I am thinking about not using the Flex sensor- unless the tuner will drop a bit of 98 in the tank to bring it down to say E60-70- but they'd probably not do this and just tell me to get a flex fuel tune.

I haven't put it in yet and $250 back into my bank account will certainly be beneficial to me right now.

So basically a good idea if running flex, bad/pointless if running straight E85 since it won't effect knock anyway- only stoich point- that's the summary i've got.

35 minutes ago, CLEM0 said:

Thank you all for the great replies.

The car plan is straight E85- as the engine isn't in great health with 130psi across all 6 cylinders on a factory 25DET- so low compression.

I want to prolong it while I save up for a rebuild. But I do hope for mid 400whp with E85 in the meantime.

I am thinking about not using the Flex sensor- unless the tuner will drop a bit of 98 in the tank to bring it down to say E60-70- but they'd probably not do this and just tell me to get a flex fuel tune.

I haven't put it in yet and $250 back into my bank account will certainly be beneficial to me right now.

So basically a good idea if running flex, bad/pointless if running straight E85 since it won't effect knock anyway- only stoich point- that's the summary i've got.

Why would you want to tune the car on e60-e70?

I don't think anyone said it was bad or pointless to use a flex sensor if running pump e85 100% of the time. 

I would say the summary is closer to - 

* Yes you can run the car on pump e85 without a flex sensor

* There are benefits to using a flex sensor even if you are always on pump e85. It's up to you if you think those benefits are worth the very small outlay to install the flex sensor.

 

5 minutes ago, Murray_Calavera said:

Why would you want to tune the car on e60-e70?

I don't think anyone said it was bad or pointless to use a flex sensor if running pump e85 100% of the time. 

I would say the summary is closer to - 

* Yes you can run the car on pump e85 without a flex sensor

* There are benefits to using a flex sensor even if you are always on pump e85. It's up to you if you think those benefits are worth the very small outlay to install the flex sensor.

 

Thank you- that came across better than how I summarised it.

I would not be getting the car tuned on 98, and if E45 and E85 are minimal in regard to knock resistance, then if I got a bad batch of E85 it wouldn't be detrimental to the performance or safety of the car- so essentially unless I do plan to run flex/98, the only benefit i'd get is consistent fuel trims/AFR and more consistent economy/cold starts.

Install the flex sensor.

One day you're going to rock up to United on a low tank of fuel thinking you'll fill up, then to find out their tanks are empty.

Now you have probably 5L of fuel left in your tank and wonder how you'll get home. That tow truck emergency call out fee + towing fees will cost more than your flex sensor.

 

  • Like 4

There's no real downside and it's not strictly required. Caltex used to serve E70 to E85. As Bill mentioned up above, United has been E80-85 pretty much forever. Never ever saw that change. I suppose the offensive price gouging for the product is worth something.

(then again, Ethanol lowers the price of 91... so... they're probably maximizing the 'cheap stuff' by keeping that Ethanol content up in E85)

1 hour ago, Murray_Calavera said:

Why would you want to tune the car on e60-e70?

I don't think anyone said it was bad or pointless to use a flex sensor if running pump e85 100% of the time. 

I would say the summary is closer to - 

* Yes you can run the car on pump e85 without a flex sensor

* There are benefits to using a flex sensor even if you are always on pump e85. It's up to you if you think those benefits are worth the very small outlay to install the flex sensor.

 

E30 is popular in my area to bump up octane enough to make enough power on our terrible fuel quality in California while not suffering too much of a range deficit. It also helps with not destroying HPFPs in GDI applications.

On 3/22/2023 at 2:10 PM, GTSBoy said:

Be aware that a worn set of rings will let more water-filled blowby gases into the sump. You will want to change your oil close to twice as often as would normally be expected for E85, unless you're happy for it to all go to shit down there.

Thanks.

I did a wet test and it jumped about 7-8psi. So i'd say rings aren't amazing.

How often would you suggest a change in oil?

10 hours ago, Dose Pipe Sutututu said:

When it smells like fuel and/or looks milky from E85 and/or when it's a dark colour.

I dunno about the smell, oil will smell like E85 if you do so much as drive it out of your driveway... 

11 minutes ago, Kinkstaah said:

I dunno about the smell, oil will smell like E85 if you do so much as drive it out of your driveway... 

jesus, how much enrichment do you have on cold start? lol...

 

2 minutes ago, Dose Pipe Sutututu said:

jesus, how much enrichment do you have on cold start? lol...

 

Not sure, I have no need for Expensive-Gouge-Juice anymore, though I do have the capacity.

I remember not needing to touch any of the enrichment tables for start with the ol Haltech PS2000. Would start perfectly with full ethanol in the middle of winter without any issues. Never had any cold start problems at all, or hot start for that matter, was the most overblown 'problem' E85 ever had. At least for me..

But ye, do an oil change then drive for 100km then smell the oil filler cap. It smells like E85 really fast in my experience and isn't an indicator that the oil is ready to be changed yet.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...