Jump to content
SAU Community

Recommended Posts

I'm planning to upgrade my injectors soonish so I've started to look around now. My current injectors are a little sus, as my fuel tank was rusted to the shithouse and some of that red stuff must have gotten through the fuel filter. Starting is difficult and fuel economy around 14L / 100km.

Getting a nistune in a couple of weeks, and apart from a 3" hiflow exhaust my HCR32 is completly stock, so I was thinking a more modern type of injector with improved atomisation would be better for response and economy, does anyone have opinions on how these ASNU / Bosch injectors compare to the Nismo ones?

http://www.asnuperformance.com.au/

  • Replies 153
  • Created
  • Last Reply

Top Posters In This Topic

Yep, not sure why but GTR injectors just seem to give poor economy from the tuner I spoke to, he said they also commonly leak through the injector body, I know mine did both of these things but I can't comment on the truth of how common it is or why.

  • 2 months later...

Sorry for thread jacking but any opinions on the ASNU1000cc injectors heard they can improve economy.

http://www.asnuperformance.com.au/gallery/High%2BPerformance%2BInjectors/ansu-performance-1000cc-injector/110282

  • 9 months later...

Old thread I know but I have a quick question, Instead of wiring in 6 resistors close to the injector can you not just wire in 1 resistor on the 12v feed before it splits in to 3 then the other 3? Just 2 conections to make instead of 12 or is there something im missing?

As it is batch fire 3 injectors fire at once, so if you multiply the resistance by 3 and use a single resistor it would work imo.

Sorry my bad divide it by 3 as V = I*R so V/I = R so if you have 3x as much current you require 3x less resistance

12/1.2 amps = 10 ohms, as 3 injectors will fire at once you have 3x as much current so 12/3.6 = 3.33 ohms

Obviously the battery is closer to 13v and hence lower amps but the theory is the same however you probably can't buy a 3.33 ohm resistor, to get an equivalent resistance of 3.33 ohms you could run 3x10 ohm resistors in parallel bunched together, be easier to solder in one big lump than putting one on each injector.

Up to you I guess.

  • 2 months later...

What is the nicest way to wire the resistor to the 3 injectors in the sub harness so you can still unplug it from the main harness when pulling the motor out?

I understand that for one injector you could use the existing wiring, but what about the other 2 in the sub harness.

Hope that makes sense

  • 8 months later...

no nistune/ ecu talk... cant even get the ecu in diagnostics mode :dry:

engine does crank, did not start when pump was hard wired, injectors are getting power

am going to install stock injectors again and redo wiring back, isnt the daily so not a big waste

  • 4 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...