Jump to content
SAU Community

Rb26 Turbo Upgrade, All Dyno Results

SLY33

By SLY33,
in Engines & Forced Induction

 Share

Recommended Posts

  • Replies 807
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Paul T
Paul T

RB 28 with GTX3584RS used as Track car HKS step 2 2.8 full counter rank rods and pistons HKS 272 exhaust cam HKS VCAM Pro with 10.2 lift Ported head - ferrera valves etc Peter

SiR_RB
SiR_RB

PMC race engines built 2.8 High compression build  N1 block, billet main caps, braced + 1/2” main studs  I beem rods 625+ bolts Custom pistons  full house head cnc + hand port

Scott Mc
Scott Mc

My R32’s previous config was setup as a Targa car, roughly 300kw @ the wheels using a pair of GT-SS's and some supporting mods. It was time for a change – my new setup is focused on track days. 

Posted Images

Lethal26 Contributor

Lethal26

Posted
Posted

Lasted 2 weeks so not bad... nah to be honest the car seem to be fine just finished it n got running after 1yr off the road plus jus paid full yr rego but shit happenes!! Now need to rebuild it hopefully it won't cost much lol

  • 2 weeks later...
Snara Collaborator

Snara

Posted
Posted
On 29.03.2017 at 4:00 PM, Nosure said:

R34 gtr nur

Rb28

Poncam 260

valve spring

gtx3582 0.82 ts t3

4inch front pipe 3.5inch catback

1650cc injectors

650awhp @ 28psi 

500hp on 5000 rpm

IMG_2128.JPG

Daamn huge lag make that GTX35 with small turbine on 2.8 :O

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted
12 hours ago, Nosure said:

The 2.8 doesn't make it spool quicker a lot. But on road it feel not that laggy.  Maybe adjust the cam gear will help the spool.  

Dial in more intake advance and pull timing out before 5k to get the turbo on faster.

Nosure Proficient

Nosure

Posted
Posted
5 hours ago, Dose Pipe Sutututu said:

Dial in more intake advance and pull timing out before 5k to get the turbo on faster.

Yes. Will adjust both cam gear next month. At moment both cam gears are untouched.  The strange thing is my reimax cam gear does not have any degree mark on it:(  it might make the tuning a little bit difficult. 

IMG_2308.PNG

  • 2 weeks later...
Christian P Contributor

Christian P

Posted
Posted

N1 Block

Tomei RB28 stroker

Tomei Poncams Type B

Tomei Gaskets - 1.2mm 8.8:1

1000cc EV14

GT2860-5

LinkG4

Splitfire coils, grade 8 plugs

Mines Super outlet Pro II elbows

Mines Frontpipe Pro

HKS Type-R Intercooler

HKS Super Turbo Exhaust

HKS Cat.

HKS Hardpipes

etc...

 

First mapping done at 1.2 Bar (1.3 Peak) running on 98 Octane - starting getting some backpressure above this but will hopefully get it to 1.5Bar with 98 octane and E85 Flex after that. 

1.jpg

  • 3 weeks later...
Steve85 Mentor

Steve85

Posted
Posted
  • N1 Block
  • Tomei RB28 stroker
  • JUN 272 9.7mm lift cams
  • Garrett GTX2863 turbos
  • HKS Fuel rail
  • Injector Dynamics ID2000 injectors
  • Link G4+ PNP Board\
  • Haltech Flexfuel sensor
  • full racepace 3.5" exhaust (tuned length headers)
  • Other items...

First tune done to engines capabilities, second tune completed to my preference, in the interest of keeping the engine in one piece. 

Full power: 505.4kW (atw) at 27psi

Final Tune: 410kW (atw) at 22psi

IMG_4364.JPG

IMG_4365.JPG

  • Like 1
ido09s Mentor

ido09s

Posted
Posted (edited)

Curious to know why you would think an engine like that wouldn't live with 500rwkw on a daily basis? the power is all in the right foot and the boost controller

We have been making 450rwkw+ on a stock block and crank for years no issues. Your combo should be good for considerably more on a regular basis

Edited by ido09s
Steve85 Mentor

Steve85

Posted
Posted
2 minutes ago, ido09s said:

Curious to know why you would think an engine like that wouldn't live with 500rwkw on a daily basis? the power is all in the right foot and the boost controller

We have been making 450+ on a stock block and crank for years no issues. You combo should be good for considerably more on a regular basis

It's not that I don't think it will, i just don't require that much power. I haven't really had a chance to open the car up to it's' maximum potential so it just seemed like a no brainer to turn it down for now. If i decide later on that it needs more go, i can always have it turned back up. 

For me, it's fast enough for the moment, so my theory here is that less power should mean less stress on components. My right foot is little bit scared of the power.

The other thing worth noting is the diff gearing has been shortened (4.375 ratios), so the car really moves. I can drive it around in 5th no problem and still have enough torque to pull from 50kph. In summary; it seemed fast enough.

ido09s Mentor

ido09s

Posted
Posted
1 minute ago, Steve85 said:

It's not that I don't think it will, i just don't require that much power. I haven't really had a chance to open the car up to it's' maximum potential so it just seemed like a no brainer to turn it down for now. If i decide later on that it needs more go, i can always have it turned back up. 

For me, it's fast enough for the moment, so my theory here is that less power should mean less stress on components. My right foot is little bit scared of the power.

The other thing worth noting is the diff gearing has been shortened (4.375 ratios), so the car really moves. I can drive it around in 5th no problem and still have enough torque to pull from 50kph. In summary; it seemed fast enough.

That's fair enough. I guess all you need to do is ask the tuner to turn the boost back up ;) we run an old Link G4, no +, and our boost is controlled through the ECU. Turn the air con on in our car and it doesn't loose power, it gives it another 15psi of boost :P 

You should try some 4.9's ;) We use them for drag racing but on the street they are insane. You runs out of puff pretty quickly though. Its an RB26 S14 hence the reason we can run such a ratio.

Steve85 Mentor

Steve85

Posted
Posted
12 minutes ago, ido09s said:

You should try some 4.9's

Wait 4.9s? That's going the wrong way for my preference. :1_grinning: That must be insane... Mine tops out at about 240-260 at the moment (i can't be sure), it was doing it pretty easy at a track day (til it broke, thanks igniter!)

I do have a switch for high boost, but low boost seems mental enough for the moment.

ido09s Mentor

ido09s

Posted
Posted
2 minutes ago, Steve85 said:

Wait 4.9s? That's going the wrong way for my preference. :1_grinning: That must be insane... Mine tops out at about 240-260 at the moment (i can't be sure), it was doing it pretty easy at a track day (til it broke, thanks igniter!)

I do have a switch for high boost, but low boost seems mental enough for the moment.

Yeah you read right, 4.9s ;) We use the 4.1's normally but swap it over when we race it. If it would get off the line it would run some decent times but it does trap 138mph all day every day :P

 

Live life a little, run high boost :D 500rwkw is fun!!!!!

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • soviet_merlin
      WGNC34 - floor mats

      By soviet_merlin · Posted

      I'd be very surprised if you can buy new OEM mats. But if you can, I want some too!  Do you have links to the variations you found? Also, where are you located? I found that Nengun is happy to list items to purchase but when you do buy them you'll get an email that it's actually discontinued. As far as I know the variations in floor mats are different colour schemes as well as automatic and manual having a slightly different shape. The automatic ones fit into a manual car without issues, but I think you'd have trouble fitting the other way around. I have photos that show the shape difference if you care. FWIW I bought sets of used floor mats in decent condition at yahoo auctions.
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Marek
      Hi everyone.

      By Marek · Posted

      Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
    • Dose Pipe Sutututu
      Ethanol Content Sensor - Always at 11%?

      By Dose Pipe Sutututu · Posted

      and it ends up being already priced in as though you're just on 91RON without any ethanol. Car will lose a bit of economy as the short and long term fuel trims bring down the AFR back to stoich or whatever it is for cruise/idle for the engine.  
×
×
  • Create New...