Jump to content
SAU Community

Recommended Posts

I want to get the seat rails moved back (bolted further back in the car) or leave them where they are, but extend the rails (weld extra lengths on) so the seat has more travel.

Does anyone know which option would be easier or more feasible? Who can perform this work? I imagine I will need to get it engineered?

This will be for the drivers seat. I've noticed in the R33 the front part of the rails is bolted to a raised section of floor, thus if you moved it back you would have to straighten this piece out. Are there any other things which come to mind?

Has anyone else done this to an R33?

Thanks in advance.

Link to comment
https://www.sau.com.au/forums/topic/95123-seat-rail-modification/
Share on other sites

Nope I haven't ever tried this, but I can't see how you would extend the rails, it would have to be moving the rails backwards. Basically you need a good workshop to help you out I'm sure they can extend the mounts to give you an extra bit of room.

Maybe new rails could be fabricated that are longer. I don't know that you could do that at home though.

I'm also 6'5" (nearly 6'6") and I have no real problems with my R34. I need to lay the seat back a bit when wearing a helmet though.

Maybe you could get a race style seat (I think Ducan can get them :)) as this would sit you lower giving you more headroom.

Do those seats need new rails?

Headroom isn't really a problem for me, it's more legroom as most of my height is in my legs.

If my left foot is on the clutch fully depressed then my knee fits comfortably under the steering wheel, otherwise, with my foot just resting on the clutch, my knee does not fit under the wheel and has to sit to the side of the wheel. Obviously, the same applies to the right hand side.

Although a spacer or dished steering wheel could possibly free up some room for my knees, my arms are already close enough to the wheel, so I'd like to actually make the seat further away.

What are the mounts that the seat is bolted to? Are they special reinforced areas of the chassis such that you couldn't simply drill new holes to mount the seat further back?

Thanks for your help guys.

You can't just move the mounting points further backwards, you need to fabricate a mounting plate the rails will go to the plate and the plate will bolt to the seat, you can get a couple of inches here easilly without too much trouble but I wouldn't go past 15cm. You will need this engineered as well.

Yes the mounting points are specially reinforced and new mounting points would need to be as well. But its not that easy because the floow is nothing like flat so the rails need to take that into account.

  • 3 weeks later...
  • 5 years later...

I'd be careful and ensure that you get any seat mod engineered, I can see popo having a field day on this if you just do a back yard job. Esp. if you also do the passenger seat and are then involved in an accident - or sell the car and it is involved in an accident.

  • 1 year later...

Mine have been moved back on bride rails but on r34 sunroof still no headroom at 6'2" but large build not skinny butt

I'm back about as far as legal you cant be passed a certain point on the B pillar or seatbelts wont work now i need monkey arms cause I have to lay the seats back still ( new seats as well)

Wilshire motor trimmers does seat mods and engineers them in adelaide but wanted to do serious mods to the floor pan mounts etc , 1400 to do 1 drivers seat , just regular mount passenger side and the customer service was lame so didnt use them , still not happy with seating location , going to look at dropping the seat inside the bride rails to gain 40mm or so

Sunroof cars loose 30mm headroom per sales manual , Damn jdm cars with no leg room lol

Funny thing is when I was in japan I saw some tall asians , like 6'5" only thin as a rail , wonder if they cuss the local cars too ?

I am 6 foot and there is around 10 inches clearance from the roof lining to my head, plenty of room, even to slide a helmet on in the car.

Sounds like you need to sell the 34 and upgrade to a V35 or M35 Stagea. :)

I'm 6'8" and actually don't find my 33 GTR too bad (relative to my Datsun 1200 Ute anyway!).

In Melbourne there is a business in Coburg (Franks Engineering) that perform seat modifications and engineers them.

I seem to remember them being pretty good price-wise.

I am 6 foot and there is around 10 inches clearance from the roof lining to my head, plenty of room, even to slide a helmet on in the car.

Sounds like you need to sell the 34 and upgrade to a V35 or M35 Stagea. :)

Hmmmm NO

R35 2013 black edition modded to hell YES

My old dodge 4x4 v10 extended cab fit ok haha piece of crap

To fix the problem - ADR rules in bin and do it even better like a rollcage with backing plates thru the floor and add crossbracing for side impacts lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...