Jump to content
SAU Community

Rb26 Turbo Upgrade, All Dyno Results


SLY33

Recommended Posts

Stock Crank

CP Pistons,

Forged Rods

1.2mm head gasket

100mm intercooler

Tomei Type B Cams

Tomei Cam gears

HKS 25/30s

Tomei Dumps

3.5" Exhaust

Walbro 460L pump

HKS 1000cc injectors

Nismo Fuel pressure reg

Haltech Platinum Pro with Flex sensor

98 @ 20psi 360kw

E85 @ 20 psi 418kw

E85 @ 24 psi 454kw :yes:

Is that 2WD or 4WD, chassis dyno or hub dyno ?

Link to comment
Share on other sites

r32 GTR

r33 rb26dett

stock engine

stock turbo's

apexi super dragger 3.5" from from pipes.

some after market front pipe(unsure brand)

apexi avc-r (15psi)

apexi power fc (self tuned)

HKS pod filters

dyno run on 2wd dyno with fuse pulled.

271rwkw @15psi

Sorry about the power colour being hard to see. the little blip at 5000rpm and 7000rpm was coil missfire

post-95424-0-93818900-1414448644_thumb.jpg

Edited by Badgaz
  • Like 1
Link to comment
Share on other sites

R32 GTR

Full Nitto bottom end

-7's

Tomei Type B's

ID1000

Power FC

320AWKW@21Psi on 98.

Currently in getting Haltech+E85.... Will report back in a million years when i get the car back.

Edited by Anfanee
  • Like 2
Link to comment
Share on other sites

  • 1 month later...

99 R34 GTR Vspec

284.4rwkw.

Unopened motor

-7's

Power FC

17psi

HKS EVC 6

Metal Cat & 3.5 inch Apexi N1 exhaust

Cam gears, Sard 700cc injectors, 19psi and a retune to come in early 2015.

Hoping to hit the magic 300 kw mark

post-74132-0-83732600-1417505129_thumb.jpg

  • Like 2
Link to comment
Share on other sites

92 R32 GTR

Head:

Tomei Valve Springs

Tomei guides and retainers

Port and polish

Tomei PonCams Type B

Tomei cam gears

Turbos:

-5's

Dump pipes

3.5" exhaust

HKS hard pipe kit

Mines intake

Fuel/Spark

HKS F-con Pro

HKS EBC

spitfire coil packs

600cc nismo injectors

Nismo race pump

R34 fuel rail

Tomei reg

Bottom end

R33 block

Nissan New crank

Nitto Con rods

Tomei forged pistons

Nismo Rings

Tomei head gasket

Tomei oil pump

Trust sump extension

Twin plate clutch

Results (will pop up dyno sheets soon)

402 ATW KW

370 KW on the road.

Link to comment
Share on other sites

GTR-33
Standard unopened engine
Brae high mount manifold
HyperGear HPVA 50mm external gate
1000cc ID Inejectors
Haltech platinum Plug in ECU
HyperGear ATR43SS-2.5 Alpha CBB Turbocharger
600x300x68mm intercooler
3inches turbo back exhaust

330awkws @ 20psi

Pump 98 fuel.

atr43ss25alpha330rwkw.jpg

atr43ss25alphaboost.jpg

Link to comment
Share on other sites

GTR-33

Standard unopened engine

Brae high mount manifold

HyperGear HPVA 50mm external gate

1000cc ID Inejectors

Haltech platinum Plug in ECU

HyperGear ATR43SS-2.5 Alpha CBB Turbocharger

600x300x100mm intercooler (red line on sheet below, the rest was using a 600x300x65mm cooler as above)

3inches turbo back exhaust


337awkws @ 20psi P98 fuel and 367awkws @20 psi E85 fuel:

atr43ss25alpha337rwkw.jpg


atr43ss25alphaboost.jpg



E85 result


atr43ss25alpha367rwkwe85.jpg


Video:




Same setup as above. Using our high flowed Ebay T67. Final result of 404awkws @ 23psi E85, limitation of fuel pump.

atr43g4power.jpg

atr4g4boost.jpg


Link to comment
Share on other sites

R34 GT-Four with rb26

Forged pistons

Billet n1 pump.

Hks 2540s

Xforce split dumps- hks twin 6mm mid pipe into 3inch exhaust.

Hks 264s 8.7mm with adj gears 1deg adv

Stock gtr intake/airbox

Hard pipe kit.

Z32 afms

Haltech pro.

Just running in it on .8lmbda on boost with 14degrees @17.5 psi 305rwkw untuned. Turned it up to 22psi. Haven't dynod it yet. Should go near 380-400kw once I tune it on e85

Link to comment
Share on other sites

Been a few months so far and still goin strong!! :yes:

RB26 S13

STANDARD R34 RB26

N1 oil pump

-5's

STANDARD R34 dump pipes into 2.75" front pipes to 3" exhaust

1400cc injectors

wallbro 460

E85

509HP - 390 RWKW

Best 1/4mile so far 11.0 at 135mph.. on about 480hp... still a rookie at drags haha ;)

http://youtu.be/J0y_oRPFPtg

post-42929-0-74841400-1420019338_thumb.jpg

Edited by BrynDETT
  • Like 1
Link to comment
Share on other sites

http://s1068.photobucket.com/user/Ptriffitt/media/866FE882-D5CD-41AE-9988-94F6E6A306B9_zpseiv9vcjy.jpg.html

My 32

This graph was from 2007 with an unopened motor

Stock turbos

Stock cams

Stock injectors

Stock intercooler and pipe work

Adjusted cam gears

Z32 AFMs with APexi filter kit

CES factory style dump pipes and front pipe

HKS super Dragger cat back

Walbro 255 intank

APexi Power FC

Exedy twin plate

Link to comment
Share on other sites

  • 2 weeks later...

R34 GTR VSPEC

Tomei 260 cams + cam gears

Nismo Afm

Power fc

Garrett -5 turbos

Hks suction kit with k&n filters

Catch can

Nismo thermostat

Arc 100mm intercooler

Hks oil cooler

Yellow jackets + Ngk platinum plugs

Nismo twin plate clutch and flywheel

Greddy profec 2 boost controller

Nismo 600cc with walbro 400l

Hks front pipe (2.75-3.5) with venom cat (3.5 with 5inch body) custom 3.5 xforce catback

350kw at 20psi

Edited by R34GTRVJONO
Link to comment
Share on other sites

  • 4 weeks later...
GTR-R33


Standard unopened engine

Brae high mount manifold

HyperGear HPVA 50mm external gate

1000cc ID Inejectors

Haltech platinum Plug in ECU

HyperGear ATR45 Special application Turbocharger

600x300x100mm intercooler

3inches turbo back exhaust


411awkws@26psi E85 fuel.


411rwkwpower.jpg


411rwkwsboost.jpg


Power and Responds Vs GT3582R on very similar setup:

vsgt3582rpowermarked.jpg

3582vsboostmarked.jpg
Link to comment
Share on other sites

  • 4 weeks later...

R32 GTR

HKS 2530's turbos

R34 Gtr dumps

Full 3.5" exhaust

Haltech Platinum Pro

Turbosmart Eboost boost controller

Tomei Type B Poncams

Adjustable cam gears

Tomei valve springs

ARP head studs

Splitfire Coilpacks

ID1000 injectors

Twin intake Walbro 255 pumps

NPC clutch

Standard bottom end

403kw @25psi on E85

Edited by France
  • Like 1
Link to comment
Share on other sites

R32 GTR

N1 Block

HKS Step 2 2.8 Stroker Crank / Rotating assembly

HKS 272 cams and valve train

Precision 6466 turbo

E85 Flex Fuel

Link G4+

6 Speed Getrag

Didnt lean on it too hard timing wise in the top end, expect to push it a touch over 800 in a few weeks

post-85139-0-76135100-1425447895_thumb.jpg

  • Like 2
Link to comment
Share on other sites

Standard RB26

Standard Fuel pump + injectors. Fuel pump direct +12v feed

Turbos either standard or N1's or something. Engine came from an imported R32 half cut so who knows. I'll check what they are when I get a chance. It just made more power than we were expecting

Standard dumps

2x2" to 3" front pipe. 3inch 100cell stainless cat. 3.5" to 4" catback (don't laugh I know it's a shitty design)

Standard ECU socketed and chip tuned by Guilt Toy himself.

post-113447-0-43048800-1425632211_thumb.jpg

270rwkw @ 17psi. 22 degrees of timing in the top end on 98 and it goes super rich from ~7500 RPM to keep EGT's down incase the turbos are indeed ceramic as 17psi is a bit beyond what's considered "safe"

Link to comment
Share on other sites

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I have been looking at some setting on the alarms for the Q60 and what buttons do and so and also been looking for details on the alarm in my V37 which is a standard issue with the car. settings like window roll up and a few others seem to not work at all. i cant seem to find exact info on V37 alarms so Q60 is all i can really go off i have not tried 400Z alarm settings or info yet so that will be next. any one got like a sheet of info on the alarm system in the V37 as all my documents are in japanese but i thought the system would basically be like standard through similar models? 
    • I had a fuel smell coming from the drivers rear and pulled the tank out to inspect where it was coming from, turns out the breather hose from the tank to the filler neck was perished. I’m going to Japan next week and I’ll grab it while I’m there  pulled the oil tank apart and started cleaning this crap out of it, some brake cleaner and rags got it looking new again 
    • Hmm. Was quite a few years ago now. I think I bought from a crowd in the US called CDT Audio. The speaker is the HD-6. The HD-6CF would have been the better option (based on T-S parameters), but they were discontinued in 4 ohm at that point in time. The HD-6 is a better driver in almost every other way (than the CF) - just not as good in IB. They still do the HD-6. They might even have a more suitable (for IB) option here.https://www.cdtaudio.com/cdtnew22/products/components/woofers/midwoofers/midwoofers.htm But, here's the rub. I was working in the US a lot back then, so I got them delivered to my US office and then just brought them back to OZ myself. I don't know if they will ship to OZ, and it probably wouldn't be great cost-wise anyway. As to results. They're driven direct off the rear channels of my headunit, because the headunit can be setup to run the rears as subs. So, not a lot of power being fed there. Nevertheless, there's no shortage of volume - the sub levels don't need or want to be boosted at all. The bass is definitely not what you would call "tight". It is definitely a bit delayed compared to a proper sub. But, with the great front soundstage and really good 6.5" woofers in the front doors, I'm getting most of the bass detail from the front and the rear is really only to extend the bottom end a bit. Works for what I'm doing. I mean - until recently you couldn't really hold a conversation in my car due to the fuel pump, and for many years I had tyres so noisy (Kumho KU36 at <50 tread depth) that I had to drive with earplugs anyway!
    • curious to know what drivers you chose and the results? quik mafs, says two 6.5s should roughly equate somewhere between a single 8" or 10" driver. i agree that IB is definitely the way to go in most cars imo.
    • S13 and R32 rear suspension geometry is horrible once you lower it (which everyone does). The camber & toe out ramp is very aggressive, hence it's common for the S13 boys/girls to use a S14 or S15 subframe as the geometry is light years ahead. I'm sure the same can be done on R32s, but I don't know anyone that has done that.
×
×
  • Create New...