Jump to content
SAU Community

Recommended Posts

This is how Gibson managed the blowby. I assume due to the small size of catch can, and the amount of boost they ran, they had it well sorted.

I would say the drained chamber over the rocker cover would be stuffed with steel wool or baffled. Not sure if the catch can is drained back to the sump, but it seems to have a breather to the sump.

post-63525-0-25680000-1417096802_thumb.jpg

less thinking more doing shit that works

in the getto

Dash ten on pasengers side
image_zps1ceccf15.jpg
Two dash 12 on the drivers side, angles and spaced so as not to hit shit and be able to tighten the f**ker up

note that they are above the windage/baffel
image_zps6bfcbf80.jpg
Baffled and shit

door hinges from bunnings
image_zps52ed1d07.jpg[/url

ml]shep7_zps01a2f7a8.jpg

dash 20 atmo vent (strait to the ground so people behind me can EADC)

getto as f**k but works a treat

  • Like 4

I've bought a rubber flappy thing that tomei makes, its their universal jobby.

On a 25 sump the passenger side doesn't allow for a vent abovethe windage tray, should I just cut it out and mount the tray lower down to allow for that?

The Gibson engine was dry sumped and scavenged from multiple points

No they weren't, grpA rules stated it had to be wet sump.

The photo of the Gibson engine bag shows only the separator, the other part of the catch can is where the battery in the R32 normally is.

This is how Gibson managed the blowby. I assume due to the small size of catch can, and the amount of boost they ran, they had it well sorted.

I would say the drained chamber over the rocker cover would be stuffed with steel wool or baffled. Not sure if the catch can is drained back to the sump, but it seems to have a breather to the sump.

9572626787_019bd1895c_z.jpg

9575419288_e3446a4643_z.jpg

9575423336_3ca4c10bb6_z.jpg

  • 3 months later...

Ok for years this even to this day has been a problem for me. Now im only on page 5 of this thread and intend on reading it all anyways. But I have a few points that I know about from reading here and on other nissan sites. The oil pump collar problem ive personally gotten over. The oil blowing out not so much. All my 25 suffer from this. I feel its the additional rpms I run like 8500rpms. And now im learning that these rb motors were ment for only 6k. Like what the hell. :angry:

Ok so ive done like 3 things out the list

1. I did the head drain

2. I did the restrictor in the block but now learning I shouldn't run 2 of them but should have blocked one out. (To late) dont mind pulling the head.

3. I did the collar.

FYI.All my 25's run N1 oil pumps.

Thats it. I have always looked at the head. The oil returns by the head bolts is what you gays are saying to drill out bigger and the same to the block.?? They seem big enough as is, as part of the washer covers a part of the hole already and if made bigger then what will the bolt/stud pull on? next is at the very back of the head there is 2 major oil drain its in the photo ill attach. What do I do to these. Just hone them out as big as I can go. ??

Last can some post photo if not already in the thread again please, as im only on page 5 at 15 pages a day is my goal:D

Now all of this said. Just a estimate here can an rb motor now do 10k all day with other issues and dont blow oil out. ????? This issue needs to be addressed.

With my rb26 build I regret now not doing the machining of the oil return ports I am running an oil accumulator and a racefab 9.5L sump cooler and a tomie oil pump 1.1 oil restrictor size.

Im so frustrated :wacko:at this. As im running a tomie oil pump as well,

And I will be spinning this motor at about 9k or more cause I dont care for it especially now. Well ill continue reading bye

That's why I suggested reading just the last 15 pages. Ideas have developed since that thread was started and oil drains at the back of the head are generally agreed to be a waste of time and proper sump venting to a catch can the way to go.

BTW RB26 and even RB30s can be made to spin to 10,000 rpm if you do it right.

Im at page 16. Well im not having this problem with my 26 as yet. But all my 25 are doing this. Ill read the last 15 pages then. I still want to read the whole thing though. Heres an idea. Just an idea though. See that other are open to menstion ideas. From the back of the head drain cant some kind of pump be added and controlled to come one at a predetermined rpm point. Using a rpm trigger switch. This pump will be inline and pump the extra oil from the head to the sump. Just an idea.

Edited by MJTru

I track my built 26 regularly and always used to fill the catch can cos I'd rev the shit out of it.

Now I've learnt to keep it below 8K rpm and can do a whole day with out touching the can.

Motor is pretty basic, standard sump with Tomei baffle, N1 pump, oil restrictor & enlarged oil returns. Just wish I had of known about putting a sump breather in years ago when it was built.

I don't actually have a breather, I meant I wish I had one fitted. If you flick a couple of pages back on this thread there should be some images of peoples set-ups hence the reason for Bob recommending to read the last 15 pages.

I am as we speak. Just to work but im am reading it as time permits. What funny is someone mentioned venting the sump would let the oil drain easier. This I read in the first 16 pages. But at that time peopel weren't jumping on board. I will go back and reread that. So venting the sump will work. Hmmmm??? if this is the case I have to mod my setup. See I only have one oil return on my racefab sump and that goes to the rear head oil return. The front turbo drain is for the single gtx3582r. I can pull the sump out to do that so im thinking ill move the head drain to the second spot that was used for the rear turbo when it was stock. Then vent the sump.

What you guys feel about that. I drag racing this car and intend on spinning the motor to 9k on some days.

Edited by MJTru

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...