Jump to content
SAU Community

Recommended Posts

Guys,

An update on the prices for RE55 R compound tyres from Donnellans. Prices have gone up a bit from the prices listed in the old thread Here.

There's a couple of new sizes available too. Available from Donnellans in Box Hill... Oakleigh shop will match the price if it's closer to you.

New prices:

[ 18" ]

Bridgestone RE55 225/40/18 . . . . . . . $376 per tyre $395

Bridgestone RE55 245/40/18 . . . . . . . $383 per tyre $405

Bridgestone RE55 265/35/18 . . . . . . . $418 per tyre $440

Bridgestone RE55 285/30/18 . . . . . . . New Size $478

[ 17" ]

Bridgestone RE55 235/45/17 . . . . . . . $348 per tyre $355

Bridgestone RE55 235/40/17 . . . . . . . $351 per tyre $366

Bridgestone RE55 245/40/17 . . . . . . . New Size $386

Bridgestone RE55 255/40/17 . . . . . . . $375 per tyre $393

[ 16" ]

Bridgestone RE55 225/50/16 . . . . . . . New Size $290

Comparison of tread pattern between older Bridgestone 540s and current Bridgestone RE55:

bridgestone.jpg

Enjoy :wub:

Cheers.

  • Replies 62
  • Created
  • Last Reply

Top Posters In This Topic

I bought a new set only a month ago for 410 each at Box Hill.

Price went up early June. I called end of May and they were $412 fitted, then called late June $440 fitted.

Something to do with the price of oil was what I was told. Great excuse for retailers if you ask me.

I know some people run these on the street, but does the sidewall make it really stiff and rough on general roads?

Ive had some Falken Azenis RT215 semi comps, they were 16's, and it was a rougher ride than the street 18's on the same car. These were back on my Commodore.

Are the sidewalls stiff like the Falken track tyres, soft like road tyres, or inbetween?

I run them on the street & they exhibit the following characteristics:

They tram line like a bitch.

The stiff side walls give you a rough ride.

They make a shit load of noise, especially at 80 to 90km/h

They pick up every bit of shit on the road & fire it up into your wheel arches.

The don't last very long.

RE55's are like the Falkens, the major difference being you get proper grip to offset the cost & the other hassles.

With a proper set up & a clean track - 1.25 laterals gees of fun should be yours to have. :O

Edited by djr81
I run them on the street & they exhibit the following characteristics:

They tram line like a bitch.

The stiff side walls give you a rough ride.

They make a shit load of noise, especially at 80 to 90km/h

They pick up every bit of shit on the road & fire it up into your wheel arches.

The don't last very long.

RE55's are like the Falkens, the major difference being you get proper grip to offset the cost & the other hassles.

With a proper set up & a clean track - 1.25 laterals gees of fun should be yours to have. :)

You forgot to say - they go fast!

But yes the above is true. (Sigh) The price we pay to go 5sec quicker per lap.

The cost of rubber these days.

Bouncing higher and higher.... :) the god rubber

So ...My Tyres are going to cost more than the rims i ordered..

And steel has gone up in price too......

I just think it is all hype to make us pay more on the products they sell....like what was said on tv

I run a small business making office chairs and i have had no problems with price rises from my suppliers

We use steel and oil based products

This Sucks....We should all get together and have group buys for this...they are ripping us off

What next...our shoes are going to up in price by !5% because of the price of petrol :)

for those interested these tyres are in fact semi compound rubber, which is suitable for track usage. they are not recommended for normal street use. you can use them on the street but they react completely different to normal street radials. they are roadworthy and acceptable as far as ADR's and vicroads are concerned however.

the expected lifetime is somewhere around 8,000k's to 10,000ks for a set.

that would be normal street use i would expect, not sure how long they would last given full track usage. ie: not sure how many track days they would last

for those interested these tyres are in fact semi compound rubber, which is suitable for track usage. they are not recommended for normal street use. you can use them on the street but they react completely different to normal street radials. they are roadworthy and acceptable as far as ADR's and vicroads are concerned however.

the expected lifetime is somewhere around 8,000k's to 10,000ks for a set.

that would be normal street use i would expect, not sure how long they would last given full track usage. ie: not sure how many track days they would last

Well I put a set on approx 12 months ago. They have done a number of track days, approx 5000kms and are completely shagged.

If you are keen enough you can destroy a set in one track day.

The other thing that amuses me is how much of a difference some people expect them to make in a one minute lap. You may be lucky to pick up a couple of seconds over a good set of street tyres. Nothing more. Certainly not the 4 or 5 seconds over a minute lap that some people believe.

Well I put a set on approx 12 months ago. They have done a number of track days, approx 5000kms and are completely shagged.

If you are keen enough you can destroy a set in one track day.

The other thing that amuses me is how much of a difference some people expect them to make in a one minute lap. You may be lucky to pick up a couple of seconds over a good set of street tyres. Nothing more. Certainly not the 4 or 5 seconds over a minute lap that some people believe.

:thumbsup:

OK then...

Lets source a great tyre on road and track.....Set up a group pricing buy with the company

and then loose control....because it hasn't cost us much

Well I put a set on approx 12 months ago. They have done a number of track days, approx 5000kms and are completely shagged.

If you are keen enough you can destroy a set in one track day.

The other thing that amuses me is how much of a difference some people expect them to make in a one minute lap. You may be lucky to pick up a couple of seconds over a good set of street tyres. Nothing more. Certainly not the 4 or 5 seconds over a minute lap that some people believe.

Phillips Island - we tested with four people and they all improved by exactly five seconds straight away.

Sandown was like 4 seconds average

A decent steerer should be able to pull four seconds easy, and come close to five seconds even at a track like Winton.

I dropped 5 seconds off my time at Winton going from streets to semis... 1.43 to 1.38.... I did have a little bit more power, but i also had some brake issues, without the brake issues i think i would of had another second or so in there.... (on that day)

I dropped 5 seconds off my time at Winton going from streets to semis... 1.43 to 1.38.... I did have a little bit more power, but i also had some brake issues, without the brake issues i think i would of had another second or so in there.... (on that day)

You would only classify the GT-SS as " a little more power". Your car is awesome :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...