Jump to content
SAU Community

Recommended Posts

  • Replies 117
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

current car: 1997 180sx type x

next car: another GTR, S2000 or perhaps a mazda FD3S

quick why?: i switched from a GTR to sil cause i like dorifto. but i miss the RB26 and 4wd grip sometimes. so may want to go to another BNR32 or BNR34

or perhaps a S2000 as i like the lightweight high reving engine.. good mix

then maybe a rotor..??

or a MX5...

i buy cars for fun rather than commuting

My last car was a 98 MX5. i'm currently in the market for somehing new, and am torn between an Evo 6 and R32 GTR.

Yesterday I was dead set on the GTR, today I saw an EVO and changed my mind, tomorrow it'll probably change again.

Decisions decisions!

I'm waiting till I get behind the wheel of both of them before I make any decisions, but what you guys think?

I'm awaiting a totally unbiased answer of course :)

R33 GTST to be replaced by 996 911 S. Probably a year or two away. That said the BMW 335i has caught my attention of late especially in it's performance during the Bathurst 24 hr.

My charade 1 ltr is to hopefully be replaced by a Renault Clio Sport.

I'll finally be happy with my garage (I hope).

Current Cars: Nissan 180SX ('92 model), Nissan Pulsar N15 Sedan.

Next Car: Well the 180sx is a long term keeper, so the Pulsar will go first. I think maybe a crewcab ute would be good. I need something that can carry four adults in relative comfort. Would be good to have a tow-car too, and something to carry spares around, so the ute would be ideal for me.

The next car that I upgrade will probably be my daily driver from a 1991 Peugeot 205 GTI to a boring 5 door VW Golf Mk V TD. I'll keep the R32 GTR for a while yet until an R34 GTR M-Spec Nur comes along or I can afford the new GTR.

  • 1 year later...

Current cars

08 Prado turbo diesel- Maybe Replace 09 [new shape] or keep and spend money on mods for gtr!

R34 Gtr- Keeping for 3 more years hopefully afford to modify more- replace late 2011 with R35

Thats if things go to plan and the economy doesnt get completely screwed!!! :thanks:

Edited by Duncan1

Fuel embargos not considered, I'd like to keep the R34 and then add...

i) a replacement R33 GTR for the one I sold 5 years ago and

ii) an R32 GTR (from Oz)

Yes, am a bit sentimental, but I figure that now I'm used to the confined space in the 4th Gen Prelude,

... I'll find the R32 quite spacious by comparison lolz.

Tez :thanks: ...the 3 GTRs will look nice together

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...